A fabric used in air-inflated structures is subjected to a biaxial loading that results in normal stresses ox= 18 ksiand oz= 24 ksi. Knowing that the properties of the fabric can be approximated as E= 12.6 x106psi and v = 0.34, determine the change in length of: (a)side AB (b)side BC (c)diagonal AC

A fabric used in air-inflated structures is subjected to a biaxial loading that results in normal stresses ox= 18 ksiand oz= 24 ksi. Knowing that the properties of the fabric can be approximated as E= 12.6 x106psi and v = 0.34, determine the change in length of: (a)side AB (b)side BC (c)diagonal AC

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An extruded polymer beam is subļected to a bending moment M. The length of the beam is L = 860 mm. The cross-sectional dimensions of the beam are bq = 36 mm, d = 89 mm, b2 = 22 mm, d2 = 22 mm, and a = 7 mm. For this material, the allowable tensile bending stress is 10 MPa, and the allowable compressive bending stress is 10 MPa. Determine the largest moment M that can be applied as shown to the beam. b2 ja a M d2 d1 A B b1 Answer: 410.8451 N-m
Two polymer bars are connected to a rigid plate at B, as shown. Bar (1) has a cross-sectional area of 1.2 in.2 and an elastic modulus of 1820 ksi. Bar (2) has a cross-sectional area of 1.185 in.2 and an elastic modulus of 3590 ksi. Assume L1=21 in., L2=48 in., Q=7.6 kips, P=2.6 kips, and R=12.8 kips. Determine the horizontal deflection of end C relative to end A.
A thin polymer plate PQR is deformed so that corner Q is displaced downward 1.3 mm to new position Q', as shown in. Determine the shear strain at Q' associated with the two edges (PQ and QR). Assume a = 64 mm, b = 100 mm, c = 80 mm, and Δ = 1.3 mm.
30. An aluminum alloy rod has a circular cross section with a diameter of 8mm. The rod is subjected to a tensile load of 5kN. Assume that the material is in the elastic region and E = 69 GPa. If Poisson's Ratio is 0.33, what will be the lateral strain? E= 6/8 v = -E(lateral)/(axial)
An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 500 mm. The cross-sectional dimensions of the beam are b₁ = 33 mm, d₁ = 109 mm, b₂ = 20 mm, d₂ = 20 mm, and a = 6.5 mm. For this material, the allowable tensile bending stress is 16 MPa, and the allowable compressive bending stress is 11 MPa. Determine the largest moment M that can be applied as shown to the beam. b₂ a M B A Answer: M = L d₂ N•m b₁ d₁
Answer in two decimal places please
An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 500 mm. The cross-sectional dimensions of the beam are b, = 35 mm, d = 115 mm, b2 = 21 mm, d, = 21 mm, and a = 7 mm. For this material, the allowable tensile %3D %3D bending stress is 15 MPa, and the allowable compressive bending stress is 14 MPa. Determine the largest moment M that can be applied as shown to the beam. b2 立 a 不 d2 d1 A Answer: N.m M= i Submit Answer Attempts: 1 of 3 used
In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown mm while those at CD decrease 70 x 10 mm in the are found to increase 50 x 10-3 280-mm-gage length. Using E = 170 GPa, determine the flexural stress at the top fiber. Answer must be in MPa. Given: a = 40 mm, b = 130 mm, and c = 80 mm. gage length a mm b mm c mm «Previous ext
SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and attached to two vertical rods. Assume that the rods were initially stress-free. Allowable stress in steel is 120 MPa and in bronze is 60 MPa. For this problem, a = 1.8m; b = 1.3m; c= 1.7m. a b C P Steel: A-900 mm² Bronze: A=1200 mm² E = 83 GPa L=2.0 m E = 200 GPa L=1.5m What is the value of P without exceeding the allowable stress of bronze, in kN? O 161 O 174 O 145 124 4
ProbleT = - An aluminum bar has diameter d = 40 mm, shear modulus of elasticity G = 27 GPa, and torque T = 300 N.m. (a) Determine the maximum shear, tensile, and compressive stresses in the bar, and show these stresses on sketches of properly oriented stress elements. (b) Determine the corresponding maximum strains (shear, tensile, and compressive) in the bar and show these strains on sketches of the deformed elements. |d=40 mm T= 300 N-m
Give me right solution with clear hand writing.
1. The column in the figure shown has a strain on its compressive edge equal to -0.003 and has a tensile strain of +0.00185 on its other edge. Detemine the nominal values of Pn and Mn that cause this strain distribution if f'c = 21 MPa, fy = 414 MPa. Draw the column interaction diagram. en 600 Pn mm 8 - 6 32mm 75 225 225 75 600