(a) Explain reasons to divide the physical memory of 8086 into segments. Suppose that DS= XX00H, BX= 0210H and DI = 0010H. Determine the memory address accessed by each of the following instructions: i. MOV AL, [1234H] ii. MOV AX, [BX] iii. MOV [BX+DI+200H], AL (hints: Replace XX with the last 2 digits of your student ID)

(a) Explain reasons to divide the physical memory of 8086 into segments. Suppose that DS= XX00H, BX= 0210H and DI = 0010H. Determine the memory address accessed by each of the following instructions: i. MOV AL, [1234H] ii. MOV AX, [BX] iii. MOV [BX+DI+200H], AL (hints: Replace XX with the last 2 digits of your student ID)

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

which one is valid instruction * LDS AL,[BX] LDS AX,[CS] DAA XOR AX,AX NOT AX,AX which one is valid instruction * IN 0245 ,AL IN DL,0245H IN AL,DL IN 0245,AL IN 0245,DL IN AL,0245
Implement the following expression in assembly language: result = (val3 + val4) - (val1 – val2) – (30*4)/55- Assume that result,val1, val2, val3 and val4 are 16-bit integer variables- You need to implement the expression the way it is provided, you cannot do any reduction on theexpression while implementing it.- Initialize val1 with 134 (hexadecimal), val2 with 139 (hexadecimal), val3 with 67(hexadecimal) and val4 with 47 (hexadecimal)- You are NOT allowed to update the values of any variables.- Use ONLY mov, add, sub, movzx, movsx, or neg instructions whenever needed.- Use the debugger to verify your answer
Implement the following expression in assembly language: result = (val3 + val4) (vall - val2) (30*4)/55 Assume that result, vall, val2, val3 and val4 are 16-bit integer variables You need to implement the expression the way it is provided, you cannot do any reduction on the expression while implementing it. - Initialize vall with 134 (hexadecimal), va12 with 139 (hexadecimal), val3 with 67 (hexadecimal) and val4 with 47 (hexadecimal) -
Memory 12200 12201 12202 12203 12204 Content %D AA EE FF 22 What result is produced in the destination operand by execution the following instruction? a- LEA SI[DI+Bx+5] b- LDS SI.[200]
Answer by True or False and correct the False: 1- The instruction : MOV [Dx+SI], Ax is allowed T 2- The instruction : MOV ES:[SI], Ax is not allowedY 3- Translate (XLAT) converts the data in AL into a number stored at the memory location addressed by Bx plus AL. 4- DWORD PTR is used to address a 16-bit data of a number stored in memory F 5- REP is an instruction used to repeat any instruction as much as the value in Cx register. F
please solution with explain Question 4: What will be the final result in memory, the shown register, and the various flag bits for each of the following program's segments: MVI A,03 ADI 02 Memory LXI H,2000 MOV M,A ADI 02 INX H A 2003 2002 S Z AC P C MOV M,A 2001 |X |x| ADI 02 2000 INX H MOV M,A ADD L
7
Translate the following C code into MIPS code. Here X and Y are stored in $s1 and $s2 registers respectively and the base address of A and B are in $s4 and $s5 registers respectively. X = 7* A[6] -4*B[7] Y = 17*(X+A[9]) A[X+1] = Y Please solve this with #proper explanation
1. Identify the addressing modes used for the source and the destination operands in the instructions that follow, a. MOV AL, BL b. MOV AX, OFFH c. MOV [DI], AX d. MOV DI, [SI] e. MOV [BX]+ 0400 H.CX f. MOV [DI]+ 0400 H, AH g. MOV [BX] [DI]+ 0400H, AL
1) Write an assembly program which computes the following formulas, and writes the result to memory: M- ( Ce ) Λ (ΑΘΒ) N= M+1 Find M and N and store the values into 100H and 101H respectively. Also, check both M and N values if they are even store number 14 to memory address 120H otherwise store number 1 to memory address 120H.You are free to use other memory locations for intermediate results. Recall: symbol shows 1's complement of the number. 64
4) Write Y86 code to multiply 3 and 5 (store result in %rcx) (HINT: add 3 to itself 5 times or vice- versa.) Execute the code on Y86 simulator. Include screenshot of code and simulator window.