(a) Draw two Engineering Stress - Engineering Strain graphs: one for a ductile metal and one for a brittle metal, marking and labelling on both graphs the Yield Stress, the Ultimate Tensile Stress, the Fracture Stress, the region in which necking occurs. Correctly label all graph axes and give correct units.

(a) Draw two Engineering Stress - Engineering Strain graphs: one for a ductile metal and one for a brittle metal, marking and labelling on both graphs the Yield Stress, the Ultimate Tensile Stress, the Fracture Stress, the region in which necking occurs. Correctly label all graph axes and give correct units.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

d) Based on fatigue diagram below, find all value intersection at X and Y axis and give the name of all the line. (Fill all related calculation below) --- [2 marks] Fatigue diagram H B D Value for 'A' in fatigue diagram above? (MPa) - (1DP} Your answer Value for 'B' in fatigue diagram above? (MPa) - (1DP} Your answer Value for 'C' in fatigue diagram above? (MPa) - (1DP} Your answer
Draw two schematic graphs using pencil showing a typical stress-strain curve for aluminum. The first graph should show engineering stress vs engineering strain, and the second graph should show true stress vs true strain. Label the showing: (i) elastic modulus (ii) proportional limit (iii) yield stress (iv)yield strain (v) fracture stress (vi) fracture strain on each graph. You may showboth graphs on one plot. Explain the difference between engineering stress and true stress.
Please help me answer this question
A material with an Ultimate Tensile Strength (UTS) of 400 Mpa is loaded cyclically about mean stress of 80 MPa. If the stress range that will cause fatigue fracture in 100 000 cycles under zero mean stress is (+,- )60 MPa, what stress range (in MPa) about the mean of 70 MPa will give the same life
Discussion : • Difficulties in testing brittle materials. • Advantages of stress - strain diagram. • Sources of error you expect in the experiment. • Define the term strain hardening and explain in which stage in the stress- strain diagram it occurs, what are its reasons, and its effects on material properties? • Compare between the brittle and ductile fracture. fr in te
Case Study Calculate the Tensile Toughness Tensile toughness measures the total energy absorbed prior to fracture and is different from fracture toughness and impact toughness. Fracture toughness measures the resistance to fracture when a flaw (i.e. crack) is present in the material. Since it is nearly impossible and costly to manufacture materials with zero or near zero defects, fracture toughness is a major consideration for all structural materials. Impact toughness measures a materials ability to withstand an impact blow (i.e. high strain rates) and is particularly important in assessing the ductile-to-brittle transition behavior (more details later). Impact toughness is also commonly referred to as notch toughness. The tensile toughness can be estimated using the stress-strain curve by measuring the area under the curve (both the elastic and plastic regions). Tensile Toughness = f Stress, σ Ty- Ey Efracture ETS Ur Ey Efracture o de = U₁ + SETS o de + Sefracture o de Ey Ey o de =…
An annealed-steel specimen has a 0.750 in. diameter and a 12.000 in. gage length. Maximum load is reached at 60,000 lbs and fracture occurs at 30,000 Ibs. For this steel, E= 360 x 10° psi. (a) Draw a sketch of stress-strain diagram for a typical steel in tension? (b) What is the ultimate tensile strength (UTS)? (c) Why does fracture occur at a lower load than the maximum load? (d) What is the elongation when a tensile stress of 30,000 psi is applied? A 400-mm-long rod with a diameter of 4.5 mm is loaded with a 5000-N weight. If the diameter decreases to 3.5 mm, compute the final length of the rod. 3. 4. A steel rod 1.5 m long and 75 mm x 75 mm in cross-section is subjected to a tensile force of 160 kN. Determine the elongation of the rod, if modulus of elasticity for the rod material is 900 GPa. 5. A hollow cylinder 4.5 m long has an outside diameter of 80 mm and inside diameter of 60 mm. If the cylinder is carrying a load of 75 kN, find the stress in the cylinder. Also find the…
A steel specimen 12mm diameter has gauge length 50mm. the steel specimen had tested via tensile test under maximum load 66KN with elongation 7.5mm, and the yield load of this specimen is 15KN with elongation 2.4mm. Calculate: 1- The engineering ultimate stress (ultimate tensile strength), and engineering strain at this point. 2- The engineering stress and strain at yield point. 3- The modulus of elasticity, and the modulus of resilience. 4- The final or fracture strain of a steel specimen, if you know that the final length of specimen after testing is 58.5mm. 5- The true stress and strain for ultimate point. any four point sir
List application related to strain energy
The figure below shows the tensile engineering stress-strain behavior for a steel alloy. (a) What is the modulus of elasticity? (b) What is the yield strength at a strain offset of 0.002? (c) What is the tensile strength? Stress (MPa) 600 500 400 300 200 100 T I 0.00 Stress (MPa) 0.04 500 400 300 200 100 0.000 0.08 0.002 Strain 0.004 Strain 0.12 I 0.006 0.16 0.20 In the previous problem, A load of 85,000 N (19,100 lbf) is applied to a cylindrical specimen of the steel alloy that has a cross-sectional diameter of 15 mm (0.59 in.). (a) Will the specimen experience elastic and/or plastic deformation? Why? (b) If the original specimen length is 250 mm (10 in.), how much will it increase in length when this load is applied?
Describe the stress-strain behavior?