(a) Draw the transfer function plot for Rin for the range 10 kn < Rin < 100 kn, assuming Rin < ZL for the entire range. (b) Assuming an ideal BJT, calculate the output impedance at the slave BJT's collector node. (c) Justify: what is the danger if Z₁ > Rin?

Q: q9-  Calculate the (approximate) data rate to bandwidth ratio (R/B)  if the energy per bit (E0) is…

A: Noise power per Hz; No=12 Energy per bit; Eo=13 Signal-to-noise ratio; SNR=10 dB To find out We have…

Q: (e) Draw the combined small-signal equivalent circuit suitable for mid band frequency range…

A: gm1=2kID1gm1=220m×0.12mgm1=3.1mSr01=VAID1r01=100.12mr01=83.3kΩ

Q: q9-  Calculate the (approximate) data rate to bandwidth ratio (R/B)  if the energy per bit (E0) is…

A: Given, The energy per bit (Eo) =  13 Noise power per Hertz (No) =12 signal to noise ratio (SNR)= 10…

Q: for the PMOS, you use, μ.Cox rather than unCox) 2. There is a common-source amplifier on the right.…

A: Step-1-&gt;

Q: 2. For the SSBSC modulator shown below: (A=5, B=0.2, C=0.01) a) identify the method of single…

A: Given:we need to do:a) identify the SSB-SC generation. b) Find the equation at the output of BM1,…

Q: 3.) A power supply circuit is shown below. For the diodes, assume Vy = 0.7V. Sketch the output…

A:

Q: Asap

A: Step 1: To design the common-emitter amplifier satisfying the given conditions, we'll follow these…

Q: (a) We need to amplify a 0.25-V signal by 26 dB. Would a BJT or FET amplifier be preferred? Why?(b)…

A:

Q: 1. Suppose the MOSFET drawn has Veh = 1 V, and Ip = 1 mA when Vov = 1 V. Vin Vdp = 5 V Rp = 5 kN t…

A: The MOSFET circuit diagram is shown below, When VOV=1V,Vth=1VID=1mA

Q: Vi RB Vcc Rc our A BJT (B=200) is implemented in an amplifier circuit, with a VCC of 15 volts. One…

A: The objective of the question is to determine the value of the base resistance (RB) in a Bipolar…

Q: 6.(20) BJT small signal model, cutoff frequency a) Suppose the PNP BJT of Figure (shown below, left)…

A:

Q: A PM modulator produces a modulated signal with the equation: EpM=10sin[27(500k)t-4…

A: PM modulation

Q: Prelab: Using the BJT large signal model for the circuit in Figure 1, determine the Vsb voltage…

A: We will find out Vbe by given current then we will find out Vbb by krichoff's voltage law .

Q: Question 1 (Mandatory) If the a digital pattern repeats itself as…

A:

BJT (Bipolar Junction Transistor)

A BJT is a semiconductor device with 3 terminals that consist of a p-n junction diode that can amplify the signal or current. It is a current-controlled device. The three BJT terminals are base, collector, and emitter. The BJT works with the charge carrier, the two type of carriers in the BJT are holes and electrons, the charge carriers flow by the process of recombination. The signal to be amplifier is generally given as the input at the base terminal and an amplified form of it is available at the collector terminal.