A) Draw the free body diagrams (including relevant forces) for sections of the beam that can be used to solve for the internal forces at C and D (assume C is just to the right of the 8-kip load) B) Solve for the support reaction forces at A and B C) Determine the normal force, shear force, and bending moment at points C and D (again assuming C is just to the right of the 8-kip load) 8 kip skip T 8 ft 8 ft 40 kip. ft 8 ft B-

A) Draw the free body diagrams (including relevant forces) for sections of the beam that can be used to solve for the internal forces at C and D (assume C is just to the right of the 8-kip load) B) Solve for the support reaction forces at A and B C) Determine the normal force, shear force, and bending moment at points C and D (again assuming C is just to the right of the 8-kip load) 8 kip skip T 8 ft 8 ft 40 kip. ft 8 ft B-

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem 6 For the following truss structure, compute: 1. All support reactions 2. Determine any zero-force members, if exist. 3. Determine the forces in all bars. Hint: Find the angle BCD. Then find the distance of C from the ground. 300 lb 300 lb A 13 ft 45° B 5 ft 12 ft D 13 ft 12 ft
An overhang beam carries a distributed load "w" and a concentrated load "P". If the maximum negative shear is -383.86666666667KN and the vertical reaction of hinge support is 316.13333333333KN, determine the following unknowns. (DRAW THE SHEAR AND MOMENT DIAGRAM) Let L1 = 5m and L2 = 2m L1 L2 Solve the value of "w": kN/m Solve the value of "P": kN Solve the reaction of the roller support.
The internal shear force V at a certain section of a steel beam is 79 kips. If the beam has the cross section shown (assume a = 2.1 in., b₁ = 3.5 in., b₂ = 7.6 in., tw = tf = 0.6 in., d = 11.6 in.), determine: (a) the value of Q associated with point H, which is located 2.1 in. below the top surface of the flanged shape. (b) the maximum horizontal shear stress Tmax in the flanged shape. a H d
Solve B Please fast
Part I. Principle of Superposition. For the beam loaded as shown, it is required to determine the distribution of internal forces and moments on the beam. El is constant. The supports at B and C are rollers and D is pinned. 10 kN 3 kN/m 3 kN/m В A 3m 3m D 3m 4 kN 1. Determine the degree of indeterminacy of this beam. 2. Solve for all the support reactions. 3. Draw the shear and bending moment diagram for the beam.
The steel beam is loaded as shown in the figure. Draw the shear and moment diagrams. 10 KN 8KN 4 KN/m 30KN- みD 5m A B hinge 5m 10m 4m k 6m Determine the vertical reaction at support D in KN.0 Determine the maximum shear force in KN.0 Determine the maximum positive moment in KN.m.0 Determine the maximum negative moment in KN.m.0
For the beam structure shown below, both C and E are rollers, support A is pinned. El is constant within the structure. (1) Determine the degree of indeterminacy of the structure. (2) Choose appropriate redundant(s), then apply the Force Method to calculate reaction forces at all supports. (3) Draw shear and moment diagrams of the beam (4) Apply the Conjugate Beam Method to calculate the vertical deflection at point B. -12 ft- 30 k ↓ B H -12 ft- -12 ft- E = 29,000 ksi I = 1,500 in.4 30 k ↓ D -12 ft-
Show solution with detailed Free body diagram/drawings.
Solve the problem using influence lines. Determine the maximum force (tension or compression) at member IH of a two-side bridge truss due to a series of concentrated load shown. Assume the loads can travel in either direction along the center of the deck, so that half its load is transferred to each of the two trusses Given: T= 2.16 U= 8.64 V= 13.5 W= 8.1 X= 10.8 Y= 5.4
Draw the shear-force and bending-moment diagram for the beam shown. Assume the upward reaction provided by the ground to be uniformly distributed. Let a = 3.3 ft, b = 3.2 ft, P = 20 kips, and w = 3.0 kips/ft. Label all significant points on each diagram. Determine the maximum value of (a) the internal shear force and (b) the internal bending moment. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number. P A C D E Answer: (a) Vmax= (b) Mmax= a B b lb b lb-ft a
Please help me