A dozer with as S-blade has pushed a normal load onto a level area. The height of this load measured at the inside edge of each track was 7 ft and 7.4 ft. The width of the load at the inside edge of each track was 8.1 ft and 8.4 ft. The greatest length of the pile was 16 ft. What is the capacity of the blade?

A dozer with as S-blade has pushed a normal load onto a level area. The height of this load measured at the inside edge of each track was 7 ft and 7.4 ft. The width of the load at the inside edge of each track was 8.1 ft and 8.4 ft. The greatest length of the pile was 16 ft. What is the capacity of the blade?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Derive an expression for SF if a cantilever carrying UDL for a part of its length from the free end.
Note: give me complete solution a,b,c,d and e. I don't want single answer. Please solve completely
A hydraulic press must be used to press-fit two components together in an assembly process. The system must generate at least 975 lb of force to perform the press fit. The piston at the input cylinder is pushed with a force of 250 lb and has an area of 30 in.2. The output can use up to 15 cylinders that are each 30 in.2. How much mechanical advantage is required to gain the necessary force ?
Solve the problems using the component method
Draw the diagram. Choose the correct answer and show complete solution.
Solve it step by step with free body diagram always use 3 decimal places
Fluid Force. A swimming pool is filled with fresh water to a depth of 7 feet measured at the deep end. There is not enough water in the pool to reach the shallow end. Assume that the pool is constucted using right angles, except where the bottom of the pool meets the end walls. Use Ah for the height of a typical strip across the face of the wall. 6. The weight density of water is 62.4 lb/ Your anwers should have units: pounds. 4 ft 18 ft 24 ft Declare your variable(s) here. Show your reasoning below: a) find the force on the typical horizontal strip (red) ? b) write an integral for the total force on the (left) wall of the pool
Please solve the problem with diagram
What is a two-force member? Illustrate schematically.
Need help with these Q2. Identify any zero force members. ( there can be more than one ) Member AB Member AJ Member BCBC Member BH Member BJ Member CD Member CG Member CH Member DE Member DF Member DG Member EF Member FG Member GH Member GJ q3. You are asked to find the forces in members GHGH and CGCG using the Method of Sections. Which members should you make a cut through? Member AB Member AJ Member BC Member BH Member BJ Member CD Member CG Member CH Member DE Member DF Member DG Member EF Member FG Member GH Member GJ Q4. Having made a cut through the members in the previous part, you next want to solve for Member GH. Which of the following equilibrium equations is the most efficient? (i.e. which one will allow you to solve for the required member in one equation?) a. ΣFx=0. b. ΣMC=0. c. ΣMH=0. d. ΣFy=0 e ΣMD=0
Draw the shear diagram for the beam. Click on "add vertical line off" to add discontinuity lines. Then click on "add segment" button to add functions between the lines. Note 1 - Make sure you place only one vertical line at places that require a vertical line. If you inadvertently place two vertical lines at the same place, it will appear correct visually because the lines overlap, but the system will mark it wrong. Note 2 - Indicate the segments for all values of x shown in the diagram. Even if a segment is a constant value 0, it should be drawn in the diagram. +0 No elements selected M V, lb 600- 500 400- 300- 200 100 0. -100 -200 -300- -400 -500- -600 50 lb/ft 20 ft 10 B 8 200 lb-ft 10 ft 30 x, ft ? Press TAB to navigate between elements on the canvas. Press ALT+M to get to the main menu. Press ALT+A to modify the attributes. Press (ALT+Q) to quit the application.
How many Frames multi-force member(s) have?