A double acting cylinder is used to transfer work-pieces in a production machine. Determine the extend and retract forces if the piston diameter of the cylinder is 80mm, rod diameter 15mm and the pressure used is 6bar. Assume frictional force is 10% of theoretical force.

Q: (9) A single thread trapezoidal metric thread has a pitch of 4mm &has a mean diameter of 18mm. It is…

A: Given data: p=4 mmd=18 mmdo=37 mmdi=27 mmm=400 kgμ=0.3 Need to determine the required torque.

Q: *3-44. Determine the magnitudes of F₁, F2, and F3 for equilibrium of the particle.

A:

Q: (5) A 2½-in square thread steel screw is used in a common jack screw. There are 214TPI. The body of…

A: Answer: (a) The efficiency of the screw only: 27.16% (b) The efficiency of the screw & the…

Q: A steel wheel of 800mm diameter on a horizontal steel rail. It carries a load of 60ON. The…

A: We have to calculate rolling force

Q: a) Each cylinder in a four-cylinder car engine has a bore diameter of 63.53 mm and the stroke for…

A:

Q: Find the coefficient of friction Friction force=230 N Normal force=1200 N

A: Given data : Normal force=N' Friction force=f   Required : Coefficient of friction

Q: D. If the critical load for the valve push for an overhead valve engine is 380 lbs, calculate the…

A: Given data as per the question Critical load =380 lbslength =1 ft=12 inEsteel=2.9 ×107 psi

Q: From the figure below, what is the rolling resistance from each wheel if they share to carry a…

A: Given data: W=18.7 kN Need to determine the rolling resistance from each wheel and required Force…

Q: Given the following data, calculate tl pressure and balance ratios (externa for both externally…

A: D=61.8mmB=52.6mmd=49.2mmF=188N To-Find:- Balanced/unbalanced=?

Q: A conical pivot with angle of cone as 100° supports a load of 18 kN. The external radius is 2.5…

A:

Q: If a cylinder had an internal diameter of 2 in and operates at a pressure of 300 psig, calculate the…

A: Write the expression to obtain the area.

Q: (7) A capstan is operated with a double square-threaded power screw. The pitch is equal to 1-in. An…

A: Given:p=1 inF=50 lbd=50 inP=2 ton =2000 Kg

Q: Calculate the pressure between a shaft with an outer diameter of 0.034 m and an inner diameter of…

A:

Q: A bolt assembly is experiencing 100 kN of force. The diameter of the head is 50mm, bolt diameter is…

A:

Q: a) If a block is on a horizontal table with a horizontal force, sketch two FBD's of the block for if…

A: When a horizontal force is applied on the block on horizontal table, Initially the friction force…

Q: A hydraulic cylinder with 15 mm diameter pushes a heavy tool during the outward stroke, placing a…

A: Given:To find:The mean stress.

Q: If I have a singular roller joint, in which total different directions can it provide a force in?

A: A roller joint typically refers to a joint or connection that allows rotation about a single axis.…

Q: What force applied to a circular cross-section of diameter 7.5in will produce the same pressure with…

A:

Q: 4 dia 16 R. 3. The grip strengthener shown in Fig. 1 is composed of a helical spring made of 4 mm…

A: Given: Diameter, dw=4 mmouter diameter, OD=32 mmnumber of turns, Nb=3.5design factor, ns=Syσs=1.1

Q: Determine all support and pin forces for the frames listed below. Include force summary table for…

A:

Q: I need the answer of question attached. Please show all the work. Thanks!

A:

Q: 4. A small race car has an aluminum hub (shown in red). The drive axle is press-fit into the hub,…

A:

Q: For the same question, the M25 Screw will be used when pressing the Nut Wheel onto the shaft.…

A: Given: The screw base diameter, d = 21.5 mm The load need to compress, F = 1218 kgf Nut surface…

Q: Please show complete work in handwritten format. Don't use chatgpt,If you use Chatgpt it will get a…

A:

Q: Outer and Inner diameter of a thrust bearing are 320 mm and 200 mm respectively . Axial load is 80…

A: Given Datad0=320mmdi=200mmW=80kNP=350kN/m2

Q: A 550 load. The shaft is also fitted with a 26 inches pitch diameter gear weighing 220 lb. This gear…

A:

Q: The squared and grounded ends of a safety valve with 7.5 coils. The coils measure 105 mm in diameter…

A:

Q: You are using a wheel and axle as a simple machine. You applied a force of 30 Ib to the rim of the…

A: Given, Wheel and axle as a simple machine. Force applied on axle, F1=30lb Force applied on wheel,…

Q: Compute the coefficient of friction Friction force=400 N Normal force=670 N

A: Given data : Normal force N'=670 N Friction force F=400 N   Required : Coefficient of friction

Q: Problem 8.4 A single-threaded square power screw is 0.5 inches in diameter with a pitch of 0.125…

A: The given data in the question is shown in the following attached image:

Q: Q2: - Find F, FR for the engine with the following data:- m, =0.9 kg, mrod=1.36 kg, L rod203 mm, cg…

A:

Q: Describe the failure of a hollow torque tube. Calculate the forces creating the failure

A: It is asked to describe the failure in the hollow torque tube

Q: A clamp coupling is to transmit a power of 13 kW to a shaft rotating at a speed of 511 rpm.…

A:

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.