a) Design a circuit using an Op-Amp comparator to turn ON (or OFF) the street lights utomatically. For this, you have a lux sensor installed on top of the street lights (facing above) that outputs a voltage proportional to the amount of natural light, as listed below: Unight, 0 lux = 1 V Udusk, 20 lux = 2 V Udawn, 80 lux = 3 V The lights require 2 V and should be ON if the light goes below 20 lux (at dusk). Hints: you may start by building the circuit as a comparator.]

a) Design a circuit using an Op-Amp comparator to turn ON (or OFF) the street lights utomatically. For this, you have a lux sensor installed on top of the street lights (facing above) that outputs a voltage proportional to the amount of natural light, as listed below: Unight, 0 lux = 1 V Udusk, 20 lux = 2 V Udawn, 80 lux = 3 V The lights require 2 V and should be ON if the light goes below 20 lux (at dusk). Hints: you may start by building the circuit as a comparator.]

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

35 - Which of the following is a two-ended trigger element that passes current in two directions?A) DiodeB) TransistorC) ZenerD) OpampE) Diac
What output voltage results in the circuit below for an input of 0.5 V. Refer to the following for the values of Rf = 413981 ohms, R1 = 16788 ohms. Express your answer up to two decimal places. ... V. 360 kQ 12 ko Round your answer to 2 decimal places.
R, R. R, out R. R. out out 20kn Figure 3 Figure 1 Figure 2
Simplify the circuit in Figure Q1(b) into a Thevenin circuit maintaining VA as output. 42 2V ЗА 160 Figure Q1(b)
... .. 0 O .. . . .O .. . e A student intends to connect a TL082 OP-AMP as a voltage follower, to "follow" the voltage generated by a potentiometer but makes some mistakes in the breadboard wiring: *He took Pin 3 and connected it to Pin 1, but this is wrong as Pin 3 is supposed to go to Pin 6, fix this. *A meter lead is supposed to go to Pin 6, the output not to Pin 1. A 3rd mistake results in no output but this he cannot discover, help him. Sketch a schematic diagram of this circuit, fixing the above (don't forget to include the Voltmeter) and determine what the voltmeter's indication will be, explaining why it is such. 12 V TL082 12 V AA OFF COM
7 Design a DC power supply with following specifications: • Use a full-wave rectifier. • Number of outputs: 3 i) Output 1 ii) Output 2 0-20 V adjustable-max 2A 0-(-20) V adjustable-max 2A ii) Output 3 • Operation temperature Constant 9V-max 2A 0-40 C Line regulation <0.01%+2 mV • Load regulation • High current and voltage protection <0.01%+2 mV Using integrated circuits is forbidden. You can only use integrated circuits in the regulator circuit.
For the differentiator op-amp circuit in Figure 5: a) If the sine wave input is V1= 0.02 sin 300x10³t what is the output voltage, v. when t= 10 ms. b) Draw the input and output waveforms. 200 ko 0.1 μΕ V1. OP Vo AMP Figure 5
Gg
As we know that opamps working on a dual power supply and both power supply should be in the same polarity. If the power supply is not similar in both the polarity the dc output will drift to either side depending on the higher amplitude of polarity and sometimes the case is like this offset nulling will become difficult to achieve So what is "offset nulling" ? Please explain
The three opamps used in this instrumentation amplifier are one of the types shown in Table Q2. Without detailed calculation, pick an opamp type and justify your choice Component CMRR (dB) Price (£) LT1180 116 2.08 85 4.2 TLC2201 95 0.6 LMH6642 88 1.28 AD8091 Table Q2
10 - What is the function of the varistor in the circuit shown in the figure?A) Increases the moment.B) It protects the engine against temperature increase.C) It protects the motor by eliminating voltage peaks.D) Provides protection against Covit-19.E) It protects the motor when the load increases.
5) With reference to the circuit diagram given below describe in detail the operation of the circuit diagram with all the applicable waveforms for output voltage, out put current and voltage across the thyristors with alpha=90 degrees Vs = Vm sin wr Vo (a)