a) Design a BJT base drive circuit with the following configuration that has a spike of 2 A at turn-on and maintains a base current of 0.4 A in the on state. The valtage v; is a pulse of O to 12 V with a 50% duty ratio, and the switching frequency is 120 kHz. Assume that V,, is 0.8 V when the transistor is on. The time constant T= 1µs. Load R, R:

a) Design a BJT base drive circuit with the following configuration that has a spike of 2 A at turn-on and maintains a base current of 0.4 A in the on state. The valtage v; is a pulse of O to 12 V with a 50% duty ratio, and the switching frequency is 120 kHz. Assume that V,, is 0.8 V when the transistor is on. The time constant T= 1µs. Load R, R:

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

During turn-on and turn-off of a power transistor, the current-time and voltage-time relationships are as shown in the adjacent figure. Observe the waveforms and calculate, 44) the OFF-state power dissipation (static); 45) the switch ON-state power dissipation (static); 46) the average switching loss for the OFF transition (dynamic); 47) the average switching loss for the ON transition (dynamic); Assume a switching frequency of 1kHz with 437V.
1. Given the circuit D, 7. a. Derive Kerit and Reriras a function of duty cycle and switching time, the maximum Kerit and minimum Rcrit- b. Derive an expression for the de conversion ratio VNg of the buck-boost converter operating in discontinuous conduction mode. c. For K= 0.1, plot VVg over the entire range 0SDS 1. d. Explain what happens to V at no load (R-co )?
3. Refer to the Characteristic curve shown in Figure I a. Draw a load line on the characteristics determined by VE = 24 V and = 3k for a fixed bias configuration. Rc b. Choose an operating point midway between cutoff and saturation. Determine the value of Rg to establish the resulting operating point. c. What are the resulting values of Ico and VCEQ? d. What is the value of ẞ at the operating point? e. What is the saturation, Icsat current for the design f. What is the dc power dissipated by the device at the operating point? g. What is the power supplied by Vcc h. Determine the power dissipated by the resistive elements Vcc ac input o signal HH C₁ Ra Is 'c}+₁ Rc VBEE Ic HE C₂ VCE ac - output signal
ECE 520 - VLSI Design (spring 2024) 1. Due in class: Thursday March 28, 2024 Homework #7 Consider the low swing driver of Figure 1, and assume that Vtn0=0.4V, Vtp0=-0.5V. a. What is the voltage swing on the output node (Vout)? Assume y=0. b. Estimate (i) the energy drawn from the supply and (ii) energy dissipated for a OV to 2.5V transition at the input. Assume that the rise and fall times at the input are 0. Repeat the analysis for a 2.5V to 0V transition at the input. c. Compute tpLH (i.e. the time to transition from VOL to (VOH + VOL) /2). Assume the input rise time to be 0. VOL is the output voltage with the input at OV and VOH is the output voltage with the input at 2.5V. Assume that K'n=100uA/V². d. Compute Voн taking into account body effect. Assume y = 0.4V 1/2 and 20F 0.6V for both NMOS and PMOS. VDD 2.5 V = (M)-15μm 'n 'P == 1.5 um 0.25 μm 3 um 0.25 μm in out 2.5V OV CL=150fF Figure 1 Low Swing Driver
AaBbCcDc AaBbCcDc AaBbC AaBbCc A aB AG I Normal T No Spaci... Heading 1 Heading 2. Title Paragraph Styles .. |.. ..|. .6 .. For the transistor shown in below figure, Calculate the value of Rg that will just make the transistor work as closed switch. Hence Bpc = 80, VBE = 0.7V, VCE(sat) =0.2V, Vcc = 12V, Rc %3D = 2.7KN. Calculate the IB, Ic and Calculate Rg. Vcc Re Rc
Subject : Electronics Engineering Draw the PNP transistor circuit in CB configuration. Sketch the output characteristics. Indicate active, saturation and cut off regions. Briefly explain the nature of these curves.
I need the answer as soon as possible
Mention how NPN and PNP transistor works?
What is Rb bias current?