1 W Asiacell1۹۲ من ۱۹۲H.W:A delta modulation (DM) system is tested with 10KHZ sinusoidal signal, 10Vp-p.At the input, the signal is sampled 10 times the Nyquist rate.a) Draw sampled signals for 50 micro second duration timeb) Draw the PAM for the sampled signal in (a) to get BW fs/2c) Draw the pulse width modulation for PAM in (b)d) State and draw the DM transmitted data stream using RB for the PAM in(b)e) Calculate the step size required to prevent slop overload error and minimizegranular errorf) Calculate the required channel BW for the DM systemg) If the receiver input is bandlimited to 200KHZ, what is the average S/N ratioh) If the PAM in (b) converted to PCM with 50mV uniform step size, calculatethe S/N ratioi) Calculate the required channel BW for the PCM system in (h)j) Discuss the results for (f,g.h,i), how can be raised the S/N with reduce therequired channel BW?Abdulrahman Aldabagh12:57 ic lul 21.02.17

Note: We are authorized to answer three subparts at a time since you have not mentioned which part…

A delta modulation (DM) system is tested with 10KHZ sinusoidal signal, 10Vp-p. At the input, the signal is sampled 10 times the Nyquist rate. a) Draw sampled signals for 50 micro second duration time b) Draw the PAM for the sampled signal in (a) to get BW fs/2 c) Draw the pulse width modulation for PAM in (b)

A delta modulation (DM) system is tested with 10KHZ sinusoidal signal, 10Vp-p. At the input, the signal is sampled 10 times the Nyquist rate. a) Draw sampled signals for 50 micro second duration time b) Draw the PAM for the sampled signal in (a) to get BW fs/2 c) Draw the pulse width modulation for PAM in (b)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q2: Assume a sinusoidal signal with a frequency of 3.5 kHz and maximum amplitude of 1v. Then this signal is applied to LDM with a bit rate of 25kbps. Find the appropriate value of step size for this modulation.
The output power of filter is 100 mW, when the signal frequency is 5 kHz. When the frequency is increased to 25 kHz, the output power falls to 50 mW. What is the dB change in power ?
The minimum bandwidth for a 32PSK modulated signal with a baud rate of 3000baud is a. 3000 Hz b. 12 kHz c. 600 Hz d. 15 kHz
Determine the Nyquist sampling rate and the Nyquist sampling interval for the signals: (b) sinc² (10071) (c) sinc (10071) + sinc (50r t)
Discuss and explain the operation of filter
Draw the spectrum of the sampled signal when the sampling rate is equal to 2.5 × 10* d) Draw the spectrum of the sampled signal when the sampling rate is equal to 1× 104 Draw the spectrum of the sampled signal at the Nyquist rte. An analog signal given by: x() = stn'(104) %3D is sampled using an ideal sampling tchnique. a) What is the Nyquist rate of this signal. Samplesec. the samplekse,
Can you solve this question please
2. The analog signal shown in the following figure is to be delta modulated. The sampling period and the step size are indicated by the grid on the figure. Draw the staircase function that follows the signal as closely as possible and write down the delta modulation output.
2nd problem only
5 a) Consider the sample sequence (5000, 5000, 5000, 5000, -5000, -5000, -5000, -5000}. These are samples of a square wave with a period of eight samples or 1ms at 16 KHz sampling frequency. What are the sinusoidal frequencies in the output waveform?
Q2: An audio signal given by 15 sin(4000nt) + 20 sin(8000nt) amplitude modulated(DSB-FC) a sinusoidal carrier wave 60 sin(100,000nt) a. Derive an expression for the modulated signal. b. Find the modulation index. c. Find the spectrum of the modulated signal. d. Sketch the spectrum of the modulated signal e. Which type of demodulation method you propose to reconstruct the audio at receiver. Why?
If the signal to be analyzed is an analog signal, then we pass the signal to an antialiasing filter where B is the bandwidth of the filtered signal. What sampling frequency (Fs) should be used to make this signal discrete/digital?