A dead-weight tester is used to calibrate a pressure transducer by the use of known weights placed on a piston hence pressurizing the hydraulic oil contained. If the diameter of the piston is 10 mm, determine the required weight to create a pressure of 2 bars. О а. 1.2 kg о Б. 1.6 kg О с. 1.4 kg O d. 1.8 kg

A dead-weight tester is used to calibrate a pressure transducer by the use of known weights placed on a piston hence pressurizing the hydraulic oil contained. If the diameter of the piston is 10 mm, determine the required weight to create a pressure of 2 bars. О а. 1.2 kg о Б. 1.6 kg О с. 1.4 kg O d. 1.8 kg

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A hydraulic press has a ram of 15 cm diameter and plunger of 1.5 cm. It is required to lift a weight of 1000 kg. The force required on the plunger is equal to:
Assuming oil has a unit weight of 60.53 lb/ft^3 and mercury with a SG = 13.55. Which statement is true? 4 in. Oil 3 in. 12 in. Water Mercury- The pressure in pipe A is greater than in pipe B. The pressure in pipe B is greater than in pipe A. The pressure in both pipes A and B are equal. O There is no pressure in both pipes.
please solve in SI units
Determine the difference in pressure (kPa) between A and B. a= 4.06 meters b= 2.96 meters b oil mercury b a
26. An open-top cylindrical tank 1 meter in diameter is 2.80 m tall. The tank floats in water with a draft of 2.30 meters. Unit weight of lead is 110 kN/m^3 a) What is the weight of tank in KiloNewtons? b) How much lead (in KiloNewtons) must be fastened to the outside bottom of the tank in order make it completely submerged in water? c) How much lead (in KiloNewtons) must be placed inside the tank in order make it completely submerged in water? (Ans. 17.72kN; 4.23kN ; 3.85kN)
Given; A hydraulic jack system (see figure) in an equilibrium condition, and data/properties as shown. Determine the Force F applied at the end of the lever arm to maintain equilibrium of the system. Neglect weight of plungers. Hint: Use the law of transmission pf pressure
7. What is the pressure value (PA) needed to achieve equilibrium for the figure shown (kPa)? a. 0.59 c. 1.02 b. 1.02 d. None of all these PA S.G=0.87 30 120 mm
The Menard-type pressuremeter consists of the probe. Describe in detail about probe.
QI. s) Q1: A 1 m diameter well penetrates vertically through a confined aquifer (30 m) thick. When the well is pumped at (2712 m³/day), the drawdown in a well 15 m away from pumped well is 1.8 m; while the drawdown in another well 50 m away from pumped well is 0.5 m. Take the maximum head is 40 m. 1- Determine the transmissivity. 2- What is the approximate head in the first well? 3- What is the approximate head in the second well? 4- What is the approximate head in the pumped well for steady-state conditions? 5- What is the approximate drawdown in the pumped well?
In a hydraulic press, the ram has a diameter of 20 cm and the plunger 2 cm. The fluid is an oil of specific gravity 0.8. Calculate the mass that can be raised by placing a mass of 100 kg on the plunger: (i)When the plunger and the ram are on the same horizontal plane, and (ii)When the liquid level in the plunger is 0.5 m above that in the ram. What is the mechanical advantage of the press in cases (i) and (ii) above?
Please show all work including unit converstions and please make sure to show all units. For P1=10+(6), so P1=16 psi for P2=20+0, so P2=20 psi for D1= 1ft for D2=0.6ft for Q=5.4 cubic ft per second