A DC series motor is driving a loadwhose torque is constant andindependent of the speed. Themotor speed is increased from1000 RPM to 1200 RPM byconnecting a diverter resistanceacross its field. Find the Armatureto the field winding current.Assume negligible drop across thefield winding and a linearmagnetic circuit

We are given that:Speed: 1000 RPMField current: Armature current: (unknown)Magnetic flux:…

Answered: A DC series motor is driving a loa…

A DC series motor is driving a loa whose torque is constant and independent of the speed. The motor speed is increased from 1000 RPM to 1200 RPM by

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: What speed (in rpm) must a two-pole rotor rotate at to produce 50HZ AC?

A: given data f=50 Hz pole=p=2 N=speed in rpm

Q: Describe the similarities in the construction of a DC motor and a DC generator.

A: From a mechanical standpoint, a DC motor and a DC generator are quite similar, but from a technical…

Q: 2. A DC motor with an internal resistance of 10 2 and a voltage constant Kv = 0.10 V/rad/sec is…

A: When load is not connected , Motor draw very less current from source We can neglect for the…

Q: The O smaller O larger the number of poles used in a stepper motor, the better the resolution

A: here we have to give relation between the number of poles and resolution.

Q: A four-pole induction motor drives a load at 2575 rpm. This is to be accomplished by using an…

Q: 8. Find the counter-EMF voltage of a permanent magnet DC motor when it runs at 2080 rpm. The…

A: The solution is given below

Q: 2.a) 50 hz induction motor has 2 poles and run at 2,850 rpm. What is the percent slip?

A: Given, An induction motor has, Number of Pole, P = 2 Rotor speed, NR=2,850 rpm

Q: What is the copper loss in the rotor circuit in kW? An induction motor is running at 40% of the…

Q: A Series Motor has an Armature Resistance of 0.2 and a Series Field Resistance of 0.3 ohm. It is…

A: Need to find back EMF of motor

Q: A 220 shunt motor has Ra= 0.05 ohm, Rsh =60 ohm and n max = 92.5% . What is the stray power loss.

Q: 3. A group of electromagnets that create flux in a d-c generator (the field circuit) has an…

Q: The following circuit is an L298 DC motor driver for OL ENB * IN2 INT SV GND 12V OUTI OUTZ E Six DC…

A: option b is the correct answer. L298 is used for two dc motor at a time. The L298N is a…

Q: How did you get a rotational/mechanical speed of 1150 rpm?

A: Note Mechanical RPM = Electrical RPM / ( Pole pair) Electrical RPM = Mechanical RPM *( Pole pair)

Q: How many parallel paths does the armature of the generator have?

Q: block diagram fro dc motor refrigerator

A: Electrical machines can be either generator, transformer or motors. They can be either Ac machines…

Q: The rotor of an induction motor has a moment of inertia of 5kgm2. What is the torque required to…

A: Given data, Inertia is given as, I=5 kgm2 Final speed Nf=1800 rpm Initial speed Ni=1600 rpm Time t…

Q: If the supply voltage in a three-phase induction motor is reduced by 10%, what will be the…

A: Given, The supply voltage of a three phase induction motor is reduced by 10 %. Let, E1=EE2=0.9E

Q: series motors has a very high starting torque because its armature resistance is small O True O…

A: Given A true or false question based on series DC motor. Please find the answer below

Q: The

Q: A 4 pole 3-phase induction motor operates from a 60 Hz supply calculate the speed at which the…

A: Synchronous speed = 120×frequencynumber of poles = 120×604…

Q: A 1-φ induction motor is being used to pump water in a multi-storied building. You need to select a…

A: The squirrel-cage motors used for centrifugal pumps (see Asynchronous motor) have high starting…

Q: A 6 pole, 50 Hz, 1-phase Induction Motor runs at a speed of 900 rpm. The frequency of currents in…

A: We need to find out cage current frequency for given motor

Q: At no load, a 250V shunt motor runs at 1000 rpm and draws 8A. Armature and field resistances are…

Q: The torque developed by a dc series motor is 44 N-m when drawing 17 A. If the current is doubled,…

Q: A separately excited DC generator has six poles and is running at 1150 rpm. The armature has 120…

Q: series motor runs at 800rpm when the voltage is 400v and the current is 25 ampere the armature…

Q: When the supply voltage to an induction motor is reduced by 10%, the maximum torque will decrease by…

A: Given, The supply voltage to an induction motor is reduced by 10%. V2=0.9V1

Q: The torque developed by a dc series motor is 32 N-m when drawing 17 A. If the current is doubled,…

Q: The stationary windings or magnets of a DC motor are called the

A: In the DC motor, there are stationary windings are also called magnet of the DC motor.

Q: As speed of D.C motor is increased the back EMF ---and current drawn --

Q: To start a synchronous motor, the frequency of the applied electric power is reduced to decrease the…

A: Electrical machines can be either generator or motors. They can be either Ac machines or DC…

Q: Why does the speed change as the load changes in the D.C series motor

A: -The schematic for the loaded DC series motor is shown in the figure below:

Q: 6: The power input to a 415 V, 50 Hz, 6-pole, 3-0 IM running at 975 rpm is 40 kW. The stator losses…

A: Given information is shown below:P= 6f=50 HzPin= 40 WPstator=1 kWPf+w=2 kWNr= 975 rpm

Q: A 240 V series motor takes 40 amperes when giving its rated output at 1500r.p.m. Its resistance is…

Q: series motor is

Q: A 250 V series motor draws a current of 40 A. The armature resistance is 0.15 Q and the field…

Q: The torque developed by a dc series motor is 12 N-m when drawing 23 A. If the current is doubled,…

A: Need to find new torque

Q: The DC compound motor is start by using the starter.

A: Answer is Four point starter For dc compound motor, We will connect the A to armature winfing L…

Q: A 240 V DC shunt motor takes 20 A and delivers 28 N.m at 1350 r.p.m, the efficiency is . O 73.63% O…

A: Given: A DC shunt motor having following specifications Rated voltage, V=240 V Current, I=20 A…

Concept explainers

Three Phase Induction Motor

The induction motor is an electric motor that runs on AC (alternating current) and it is of two type single phase motor that work on single-phase power supply and three-phase motor that work on three-phase power supply.

Question

A DC series motor is driving a load
whose torque is constant and
independent of the speed. The
motor speed is increased from
1000 RPM to 1200 RPM by
connecting a diverter resistance
across its field. Find the Armature
to the field winding current.
Assume negligible drop across the
field winding and a linear
magnetic circuit

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given

VIEW

Step 2: Solution

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 17 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

In DC series motor when flux increases, the speed will remains same decrease O zero increase
The torque developed by a dc series motor is 16 N-m when drawing 23 A. If the current is doubled, the torque developed becomes N-m.
Electric motors works on the principle of O a. Couple O b. Torque c. Capacitor O d. Friction
divided by rpm. Torque equals horsepower 5252 a. b. horsepower x 5252 voltage x horsepower C. d.
A 3-0, 6 pole, 50 Hz IM has a rotor speed of 987 rpm. Find rotor frequency? E) 60 Hz. F) 0.65 Hz. G) 0.75 Hz. H) 0.70 Hz.
Why do you keep the alternator speed constant in this experiment?
A 240 V series motor takes 40 amperes when giving its rated output at 1500r.p.m. Its resistance is 0.3 ohm. Find what resistance must be added to obtain rated torque at 1000 r.p.m. 2 1.9 2.1 1.8
DC shunt generator may fail to generate in the case of O Small resistance Existence of frequency Absence of residual flux High speed
A compound motor short draw a current of 50 A at a voltage of 220 V it rotates at a speed of 1200 rpm Calculate the reverse electromotive force if the resistance of the product is 0.04 ohm the resistance of the series windings is 0.01 ohm and the resistance of the parallel windings is 125 ohm then Calculate the torque generated
Drive the law of the Maximum Power require ment for a DC motor which state s that Eb-V 2 Ia Ra= %3D or
A 4 pole induction machine is working as an induction generator. The generator supply frequency is 60 Hz. The rotor current frequency is 5 Hz. The mechanical speed of the rotor in RPM is
A series motor has an armature resistance of 0.2 ohms and a series field resistance of 0.3 ohms. It is connected to a 240V supply at a particular load runs at 24 rev/s when drawing a 15A from the supply. Calculate the speed of the motor when the load is changed such that the current is increased to 30A. Answer is in rev/sec.