A damn having a triangular section has a vertical face 24 m high and base 12 m wide. Use sg=2.4 a. determine the height of water that could rise on the vertical side of the dam so that the maximum intensity of pressure at the toe is twice the average pressure at the base. Neglect hydrostatic uplift. b. What is the shearing stress at the base?

A damn having a triangular section has a vertical face 24 m high and base 12 m wide. Use sg=2.4 a. determine the height of water that could rise on the vertical side of the dam so that the maximum intensity of pressure at the toe is twice the average pressure at the base. Neglect hydrostatic uplift. b. What is the shearing stress at the base?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For a linear stress variation over the base of the dam and neglecting hydrostatic uplift. 70m note: sg concrete=2.5 40m 60m 10 6. Locate where the resultant crosses the base a. 5.59 m b. 6.28 m c. 8.42 m d. 10.51 m 7. Compute the maximum compressive stress at the base a. 1390 kPa b. 1186 kPa с. 463 kPa d. 508 kPa
Subject: Statics of Rigid Body Show Complete solution
A gravity dam of is 27 m high and has a thickness "x" of 5 m at the top as shown below. Water upstream stands 2 m below the crest of the dam. The specific gravity of masonry is 2.4. a. Find the base width B of the dam. Neglect hydrostatic uplift. b. Determine the factor of safety against sliding and overturning. Neglect hydrostatic uplift. Use u = 0.45 c. Considering uplift pressure to vary uniformly from full hydrostatic pressure at the heel and zero at the toe, find the base width B of the dam. 25 m
NOTE: ANSWER SHOULD BE ON THE CHOICES
The height of the reinforced concrete water dam in the figure is L width a. The unit weight of the body of the dam Su gola Betogarme su bendi is y=24 kN/m'. Since the height of the water lake is h and the lateral water thrust to the body is H=5h? kN/m, determine the maximum water height (hmax) to avoid 4. tensile stress at the base of the dam. (L=15m, a=7m) Note: Calculate for unit height (taking 1 m),
A masonry dam with one end face vertical, has a base 3.3 m and 7.2 m high. The vertical face is subjected to water pressure, the (s 2.4) triangular in cross section, water standing 4.5 Neglect hydrostatic uplift. Compute the following: above the base of the dam. a. The vertical reaction of the foundation. b. Distance of the vertical reaction from the heel. c. Factor of safety against overturning.
A 3 m high, 6 m wide rectangular gate is hinged at the top edge at A an is restrained by a fixed ridge at Bas shown in Figure Q1(d). Calculate the hydrostatic force exerted on the gate by the 5 m high water and determine the location of the pressure center.
e. unit horizontal shearing stress at the base in kPa
A concrete dam retaining water is shown. Assuming that there is a hydrostatic uplift that varies uniformly with 80% of the hydrostatic head from the heel to zero at the toe, compute for: a. Hydrostatic uplift force, U b. Factor of safety against overturning c. Minimum pressure at the base of the dam Specific weight of concrete = 23.5 kN/m^3 Coefficient of static friction = 0.5 Coefficient of kinetic friction = 0.4 2m 7m Water
1. A masonry dam of trapezoidal cross section, with one face vertical and horizontal base. The dam is 8-m high and has a thickness of 70-cm at the top and 4-m at the bottom. The unit weight of the masonry is 23.450 N/cu.m. What is the depth of water on the vertical side if the resultant force intersects the base at the downstream edge of the middle third. Neglect the hydrostatic uplift.
A masonry dam of a trapezoidal section with one face vertical is 0.60m thick at the top and 3m at the bottom. It is 6.60m high and has a horizontal base. On the inclined face water stands 4.5m deep. Assume sp.gr. = 2.4 for the dam and hydrostatic uplift varies. from 60% at the heel to zero at the toe. Use sp.gr. = 7.4 for concrete. c) What is the factor of safety against overturning? d.) What is the factor of safety against sliding assuming M=0.51 e) what is the intensity of pressure at the toe?
1. Determine the force F per metre width (into the page) of the rectangular prismatic concrete block shown on the figure below, that would lead to sliding of the block. The water depth is 10m and the unit weight of concrete is 24 kN/m³. 10m 5m 2.5m Sand sea bed, d=p²=35°