A dam 6m on top, 12m at the bottom and 20m high has water 15m depth acting on its vertical side. 1. What is the total hydrostatic force?

Q: What about Mohr's circle?

A: In the previous question, Given: The diameter of shaft, d = 20 mm = 0.02 m The maximum bending…

Q: Write the formula for the time required to fill the cavity by the bottom gating system.

A: Given: Bottom gating system

Q: A 1 Cutting Fluids 2 HSS 3 Serrated or segmented chips 4 Vertical shaper 5 Milling B Chip load 7…

A:

Q: %o change in diamefesx-?

A: Given; Solid cylinder of; diameter,d1=120 mmheight,h1=50 mmTwo frictionless flat dies to a…

Q: Determine the y_bar coordinate of the composite shape. Treat the bent corners as square and ignore…

A:

Q: 5. Work-energy principle to be useful in determining the change in the speed of a particle during a…

A: Work energy principle to be useful in determining the change in the speed of a particle during  a…

Q: Figure shows a heat exchanger designed to cool 5250 kg/h of an ethyl alcohol solution (Cp = 3810…

A:

Q: Differentiate between single acting and double acting cylinders.

A: Differentiate between Single Acting & Double Acting Cylinder :

Q: dy 35+メ9

A: The provided differential equation is given as, dydx=3y2+xyx2

Q: hi still waiting on the last part of the question..

A: Application of ballast tanks in aerospace

Q: QUESTION 2 A single-cylinder, 4-stroke, 3-liter gasoline engine operates at 716 rpm and a…

A:

Q: Which of the following statement is correct O 1. Reynolds number depends on the viscosity of fluid O…

A:

Q: The column consists of a wooden post and a concrete footing, separated by a steel bearing plate.…

A: Given data: The working stress for wood is σWood=1100 psi The working stress for concrete is…

Q: The coefficient of bend value in the energy loss due to bend in a pipe depends on the pipe diameter,…

A: Coefficient of bend value depends on ?

Q: The Taylor's tool life component is 0.3 and constant is 120 for a cutting tool A and 0.5 and 30 for…

A: Given:nA=0.3CA=120nB=0.5CB=30

Q: Place the labels with the most accurate description on the micrograph at locations A, B, and C, as…

A: given; Place the labels with the most accurate description on the micrograph at locations A, B, and…

Q: P? P G P

A:

Q: tan30*sin30

A: Given, Value of tan30 and sin30 is, tan30°=0.577sin30°=0.5

Q: A cross-section of a beam is shown in Figure Q2. If the shear force in this section is V = 180 KN,…

A: Given : The shear force in this section is The diagram is,

Q: Members ABC and DEF are joined with steel links (E = 200 GPa). Each of the link is made of a pair of…

A:

Q: Calculate the linear speed of the needle at the instant that theta equals 30 degrees and the wheel…

A: To find - The linear speed of the needle at the instant that theta equals 30 degrees and the wheel…

Q: F L 30 F L A E L L L L В D M

A: Drawing the free body diagram of the given system:-

Q: Wind flows over a flat plate of length L = 25 mm and width W = 8 mm. The plate is maintained at a…

A:

Q: Label all forces that act on the metal

A: A piece of metal is submerged in the liquid and one end of the metal piece is fixed with a string.…

Q: Draw the three views and a section elevation:

A: The three views and Sectional Elevation views are drawn with the scale 1:1.

Q: -d12 The figure shows a tabletop experi- nent that can be used to determine an unknown homent of…

A:

Q: what happened with the 10 in the first equation?

A:

Q: Please help. Written on paper not typed on computer or keyboard please. Need help on all questions.…

A:

Q: Y 8 12 8 12 R= 3

A:

Q: where do you get the form factor (y=.337) from? Please.

A: Form factor for full depth 20° at 24 teeth can be taken from standard table. I have provided the…

Q: The L2 steel bolt as shown in Figure 4 has a diameter of 5 mm, and the link AB which is made from…

A:

Q: Define and explain hookes law

A:

Q: Q// Drow the 5.8.0 and B,m.D yougN

A: The shear force diagram for the beam is

Q: Question No. 5 Find out the missing number in the series given below: 6, 13, 28, 59, ?, 249 O 124 O…

A: here, (6×2)+1 =13 (13×2)+2= 28 (28×2)+3 =59 (59×2)+4 = 122 (122×2)+5 = 248

Q: 2? Would it be .4070? Or would it be .4070/.4

A: 2) it would be .4070/.4065

Q: Indicate whether the terms are like or unlike. - 322, 5z? ... The two terms 5z and - 3z are

A: The two terms 5z2 and -3z2 are like terms.

Q: During the governor regular working time the sleeve moves up with 16mm due to the effort of 225N…

A: Given that, The effort of the governer, F=225 N and the movement of the sleeve is, x=16 mm=0.016 m,

Q: name these lines

A: The names of the given lines is given below.

Q: 3. Write the information from the following weld symbol.

A:

Q: What does the shear flow measure?

A: The shear flow is defined as the shear force per unit length in a thin walled perimeter. The…

Q: From the following identify the true statement. O In electrical safety precaution, all non-metallic…

A: out of the 4 statements