handle should be identified as a point of interest. Determine the Degree of freedom.

Q: 2.59 Find the force P needed to hold the 3-m-wide rectangular gate as shown in Figure P2.59 if: 1 =…

A: W=3m part a  l=2m part b  l=4m part c  l=5m

Q: Water flows through a pipe as shown in the figure. The pressure at points 1 and 2 respectively is…

A: According to the given data R1=3.30cm=0.033m R2=1.30cm=0.013m Taking previous calculated values of…

Q: 16. The figure below shows three different arrangements of materials 1, 2, form a wall. The thermal…

A: Given∆T=20°C k1>k2>k3

Q: Determine the moment of inertia about the neutral axis. 50 mm 50 mm 50 mm A B 50 mm 50 mm 50 mm

A:

Q: Under which of the following conditions can the viscous forces be neglected? O when all velocity…

A: Introduction The viscous force is the fluid's internal resistance force in response to the…

Q: 2.92 For the object shown in Figure P2.92, calculate SA for neutral stability when submerged. А 80…

A: Dear Students The answer is given below

Q: What does the internal moment cause?

A: Internal moment are actually the moments due to the resisting forces generated when the cross…

Q: 1.5m 1.5m x A C. B 2m/2 D (0.0.3) ( / B (5, 0, 3) FAB Z W C (-5, 0, 3) FAC A (0.2.1.5) C 5m E(0. 4.…

A:

Q: 5/4 Specify the x-, y-, and z-coordinates of the mass center of the quarter-cylindrical shell. 360…

A:

Q: at is the internal normal force?

A: In a beam,  The sum of all the axial force acting at a section of a beam is called as internal…

Q: 4. A standard brick (dimensions 200mm x 100mm x 65mm) is compressed lengthwise by a force P as…

A:

Q: Rod ABC has a diameter of 30 mm at AB and diameter of 20 mm at BC. the whole rod is subjected to a…

A:

Q: 8 6 C 111 D Pin 8000 T Pan A B - UT 5 t Compute the pin reactions at all of the pins

A: Given: The force acting between the point C and D is: →F=8000 N If the reactions at pin A and pin B…

Q: In the figure, a 3.50 g ice flake is released from the edge of a hemispherical bowl whose radius r…

A: Disclaimer: Since you have asked multiple questions, we will solve the first question for you. If…

Q: A fatigue cycle has a minimum stress of 21 ksi and a maximum stress of 53 ksi. The R- Ratio is: O…

A:

Q: For the simply supported beam shown, derive the Moment and the elastic curve equations in terms of…

A: Given:-  F=30kN               UDL=20kN/m      Integration constants C1=150, C2=70    RA and Rc are…

Q: ratio of connecting rod length to crank radius.

A: Given; Consider the triangular forned by the connecting rodand the crank of an IC engine as two…

Q: Find the force in member AB D E 4m a. 2kN compression b. 4kN Compression O c. 2kN tension O d. 4kN…

A:

Q: The transformation from the last joint to the tool contains a rotation of 90 degrees. Select one:…

A: That is true, as we know that the transformation from the last joint to the tool contains a rotation…

Q: A thermally operated contact mechanism is shown. If heated above the ambient temperature of 20°C…

A:

Q: What is the normal force applied to the block?

A:

Q: A reversible heat pump delivers 3.5 kW of heat to a space that is kept at 25 C, while the outside…

A:

Q: What is the normal reaction at B (Bv)? For items 13-20, refer to the compound beam shown. Note:…

A:

Q: Determine the gauge pressure at P in the figure below which shows a compound manometer. Take all…

A: GIVEN DATA- A MANOMETER GIVEN WE HAVE TO FIND GAUGE PRESSURE AT P

Q: A compression spring is to be made from ASTM A227 steel wire, with a wire diameter of 8.0 mm, and is…

A:

Q: M25x6-4h5h-23   describe each part

A:

Q: The structure below is made from stock (same stock for A-B-C and B-D) that is 5 mm thick (into the…

A:

Q: what is the length of each bar once both have been elongated

A: The area of bar A is The modulus of elasticity of A is The uniformly distributed load in bar A and B…

Q: 0.3 D 0.6 D 0.3 D 0.5 D 0.3 D 4 D 2 D 3.5 D |0.5 Di

A: front view

Q: Suppose that a particular machine in a factory has two steel pieces that must rub against each other…

A: According to Bartleby guidelines, we can solve only one question at a time. Please post other…

Q: 1 Problem 9.19 Determine the equivalent state of stress on an element at the same point which…

A: Here, Plane stress condition is given, we can solve this problem by analytical as well as by Mohr's…

Q: draw the assembly in cross-section.

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: With the chamber-pipe system in the figure, the ideal fluid (water) taken from the infinitely sized…

A:

Q: 1. For the composite shape a) Determine the location of the centroid b) Determine the moment of…

A:

Design of Shafts and Shaft Components

The shaft is basically defined as the machine element that rotates, is in circular cross-section, it is majorly used to transfer the power from one part of the system to another, or from a power generating machine to a power absorbing machine. The shaft is supported on bearings and is rotated with the help of a set of gears or pulleys that are used for the power transmission. Bending moment, torsion, and an axial force act upon the shaft. Designing of shaft primarily involves determining stresses at a critical point in the shaft that is arising due to loading.