A cylindrical steel pressure vessel 500 mm in diameter with a wall thickness of 25 mm, is subjected to an internal pressure of 5.25 MPa. (a) Calculate the tangential stress in the steel (b) Solve for the longitudinal stresses in the steel. (c) To what value may the internal pressure be increased if the stress in the steel is limited to 125 MPa

A cylindrical steel pressure vessel 500 mm in diameter with a wall thickness of 25 mm, is subjected to an internal pressure of 5.25 MPa. (a) Calculate the tangential stress in the steel (b) Solve for the longitudinal stresses in the steel. (c) To what value may the internal pressure be increased if the stress in the steel is limited to 125 MPa

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.2.5P: A hemispherical window (or viewport) in a decompression chamber (see figure) is subjected to an...

See similar textbooks

Similar questions

: A hollow, pressurized sphere having a radius r = 4.8 in, and wall thickness t = 0.4 in. is lowered into a lake (see figure). The compressed air in the tank is at a pressure of 24 psi (gage pressure when the tank: is out of the water). At what depth D0will the wall of the tank be subjected to a compressive stress of 90 psi?
A hemispherical window (or viewport) in a decompression chamber (see figure) is subjected to an internal air pressure of 85 psi. The window is attached to the wall of the chamber by 14 bolts. (a) Find the tensile force Fin each bolt and the tensile stress (T in the viewport if the radius of the hemisphere is 14 in. and its thickness is 1.25 in. (b) If the yield stress for each of the 14 bolts is 50 ksi and the factor of safety is 3.0, Find the required bolt diameter. (c) If the stress in the viewport is limited to 500 psi, find the required radius of the hemisphere.
Solve the preceding problem for an element in plane stress on the bottom surface of a fuel tanker (figure part a); stresses are sx= 105 MPa, sy. = 75 MPa, and ??xy= 25 MPa. Determine the stresses acting on an element oriented at an angle ?? = 40° from the x axis, where the angle is positive when counterclockwise. Show these stresses on a sketch of an element oriented at the angle ??.
A brass plate with a modulus of elastici ty E = 16 X 106 psi and Poisson’s ratio a = 0.34 is loaded in biaxial stress by normal stresses r and cry. (sec figure). A strain gage is bonded to the plate at an angle 4 = 350 If the stress o is 10,700 psi and the strain means used by the gageise = 390 X 106.whatisthcmax- imum in-plane shear stress (Tr, ),. and shear strain (>‘ ).? What is the maximum shear strain (y ) in the x-: plane? What is the maximum shear strain (y ).. in the y-r plane?
A composite square member of varying sizes is subjected to axial forces along its centerline, as shown. The members' cross-sectional dimensions, from smaller to larger, are 50 mm ´ 50 mm, 75 mm ´ 75 mm, and 100 mm ´ 100 mm, respectively. (a) What are the normal stresses (in MPa) induced in the bar material at Section A-A, Section B-B, Section C-C? (b) What are the changes in the axial (4.28 ft), width (100mm), and thickness (100 mm) direction (in mm), at Section C-C? Assume n = 0.25 and E = 200,000 MPa., 1 ft = 0.3048 m
6.13 A brass rod is a firm fit inside a steel tube 2 cm inside diameter and 4 cm outside diameter when the materials are at 15°C. If the rod and tube are now heated to a temperature of 150° C, calculate the maximum stresses in the brass and steel. Take the coeffi- cient of expansion for steel and brass as 10.8 × 10-6 and 18 x 10-6 per °C respectively. For steel E = 200 GPa and for brass E = 85 GPa. Poisson's ratio for both = 1/3. Neglect longitudinal frictional forces between the rod and the tube. %3D eleo
(1) A steel cylinder (Øyp = 260 MPa) of inner radius a and outer radius 3a is subjected to an internal fluid pressure pi (Note: ratio of wall thickness (t) to inner radius indicates that this is a thick-walled cylinder). (a) Determine (i) the maximum radial stress (ơmax); (ii) the maximum tangential stress (o0max). (b) Determine the limiting values of p, using: (i) the maximum distortion energy theory of failure; and (ii) the maximum shear stress theory of failure. (Hint: Maximum radial and tangential stresses occur at the same radial distance, see slide 8 of Lecture 9 notes); use these maximum stresses as your principal stresses). (c) A steel gun barrel of inner radius 0.6 m is subjected to an internal explosive pressure of 80 MPa. The tensile and compressive elastic strengths of the material are 320 MPa. Assuming a factor of safety of 2, design the wall thickness of the gun barrel.
A cylindrical steel pressure vessel 60 cm in diameter with a wall thickness of 30 mun, is subjected to an internal pressure of 6 Nmm. (a) Calculate the tangential and longitudinal stresses in the steel. (b) To what value may the internal pressure be increased if the stress in the steel is limited to 200 MN/m?
Q1
Please answer quickly
A circular plate with simply supported edges subjected to a uniform pressure of P=900 KPa, as shown below, is considered. The plate thickness is h=8 mm, and the plate radius is RO=920 mm. If Young's modules and Poisson's ratio are assumed to be E=80 GPa and V=0.5, respectively, workout the absolute maximum radial stress of the plate centre in GPa. (NOTE: round-off your answer to 4 decimal places, and write your answer without considering the negative (-) sign). ↓ P Lr> Ro st 7
A cylindrical steel pressure vessel 400 mm in diameter with a wall thickness of 20 mm, is subjected to an internal pressure of 4.5 MPa. (a) Calculate the tangential and longitudinal stresses in the steel. (b) To what value may the internal pressure be increased if the stress in the steel is limited to 300 MPa and desired factor of safety is 1.5?