A cylindrical rod 500 mm long, having a diameter of 12.7 mm, is to be subjected to a tensile load. If the rod is to experience neither plastic deformation nor an elongation of more than 1.3 mm when the applied load is 29,000 N, which of the four metals or alloys listed below are possible candidates? Justify your choice(s). Material     Modulus of Elasticity (GPa ) Yield Strength (MPa)   Tensile Strength (MPa) Aluminum alloy      70                                   225                               420 Brass alloy            100                                    325                               420 Copper                  110                                  210                               275 Steel alloy             207                                  450                               550

Q: A cylindrical rod made from an unknown metal is 350mm long and has a diameter of 10mm. The rod is…

A:

Q: You have been asked to draw up a specification for a ceramic cladding tile that is likely to…

A: Critical stress formula in terms of Youngs Modulus, surface energy and crack length is used.

Q: A cylindrical rod 100 mm long and having a diameter of 10.0 mm is to be deformed using a tensile…

A:

Q: The Yield strength/Elastic limit read from a stress stain curve is... O The transition to brittle…

A: Given:Elastic limit: This is the point in the stress strain curve where materialchanges its…

Q: How can you determine the modulus of elasticity and the modulus of rigidity of the material?

A: The expression to determine the modulus of elasticity is, Here, Y is the modulus of the elasticity…

Q: A steel rod, 2 m long and 20 mm x 20 mm in cross section, is subjected to a tensile force of 40 kN.…

A:

Q: When a tensile force of 0.6 kN is applied to an elastic element, it has an elongation of 3 mm. What…

A:

Q: A wire with a diameter of 9 mm is to be used to suspend a static load of 20 kN. If a safety factor…

A: Given data  diameter of wire (D) = 9 mm Static load acting on the wire (P) = 20 kN The factor of…

Q: You are given three metal test samples, with the same chemical composition and differing yield…

A: Given: Yield stress: A - 120 Mpa B - 140 Mpa C - 160 Mpa Grain size: A - 100 mm B - 25 mm To find:…

Q: Based on Figure Q10, the LOWEST toughness belongs to

A: Toughness is the ability of the material to withstand shock load. And toughness is…

Q: When an aluminum tensile sample with an initial diameter of 12.827 mm was tested, a maximum load of…

A: Given Data ⇒ Maximum load(F1)=66.72 KN Engineering strainε1=0.4 Engineering strainε2=0.2

Q: As a material scientist, you have been requested by an engineer to list down a possible cylindrical…

A:

Q: You are given a 10-cm-diameter cylindrically shaped extruded bar (length = 50 cm) of an aluminum…

A: The anisotropic fracture toughness behavior should be an exhibit by the extruded bar with the lowest…

Q: Question 2. (a) A cylindrical rod of length 120 mm and 15.0 mm diameter, is to be deformed using a…

A: titanium alloy and steel alloy are possible candidatesif you have any doubts please comment here

Q: . A bar subjected to a stress of 1 GPa develops an elongation of 5mm. If the initial length of the…

A: These questions are based on the concept of strength of Material.

Q: Define the term Stiffness? of materials?

A: Stiffness: Stiffness is a property of material due to which an object resists deformation when an…

Q: A tensile force of 200 KN is applied on a 0.02-m diameter and.2-m long rod. After applying the load,…

A:

Q: Question 9. A cylindrical bar of 10.00 mm diameter of some metal is deformed elastically by an axial…

A:

Q: A 0.013 m diameter, 0.5 m long cylindrical metal bar is subjected to a compressive force of 8,500 N.…

A:

Q: cylindrical rod 500 mm long, having a diameter of 12.7 mm, is subjected to a tensile load of 30,000…

A: Given, L = 500 mm d = 12.7 mm P= 30,000 N

Q: A cylindrical rod 380 mm long and having a diameter of 10.0 mm is to be deformed using a tensile…

A:

Q: A tensile force of 120 kN is applied on a 0.02-m diameter and 2-m long rod. After applying the load,…

A: The original diameter of the shaft=0.02m=20mm Force applied =P=120kN We need to find The engineering…

Q: You have been given the following test sample data following mechanical testing of 15 test pieces of…

A: GIVEN:   TO FIND:

Q: A cold drawn 1144 Stressproof steel specimen with a diameter of 0.874 in. and a 1.0 in. gage length…

A: Given: The diameter of specimen, d = 0.874 in The length of the gage, L = 1.0 in

Q: A certain structural steel rod 50cm long and 2.5cm in diameter is able to carry an axial tensile…

A: Given: Steel rod : L = 50 cm  D = 2.5 cm  To find: Weight reduction after using magnesium

Q: (a) Which material has the lowest Young's Modulus? (b) Which material has the highest elongation at…

A: as per given question  (a) Which material has the lowest Young's Modulus? (b) Which material has the…

Q: How does the resilience of this material compare to its toughness?

A:

Q: The accompanying figure represents the "stress vs. strain" plot of a brittle material Al2O3. What is…

A: Given data:- Brittle material Al203 To find:-the compressive strength of this material

Q: Question 5 A solid circular cross-section rod made up of aluminium having 20 mm diameter and 300 mm…

A: Find the yield stress and youngs modulus and total length just after fracture.

Q: A round aluminum [E = 70000 MPa] rod must be designed for the following specifications: (a) The rod…

A: The minimum diameter of the rod. Given: The length of the rod is l=2.28 m. The load applied on the…

Q: The stress-strain relation shown in the Figure below was obtained during the tensile test of an…

A:

Q: Calculate the modulus of resilience (in MPa) of a material if it has a yield stress of 500 MPa and a…

A:

Q: 19 Consider a cylindrical specimen of some hypo- thetical metal alloy that has a diameter of 10.0 mm…

A: Problem is based on strength of material and can be solved as :

Q: Which material is NOT capable of holding a static load at 600 °C? Magnesium Nickel Aluminium…

A:

Q: A steel rod 22 mm in diameter and 1000 mm long is required to have an elastic strain energy of 90…

A:

Q: Figure 2 shows the stress versus strain curve of four engineering materials. Compare the ability of…

A: The area of the stress-strain curve gives the ability of energy stored by the material.

Q: the maximum elastic elongation on the bar due to the load must be less than 0.25 mm;

A: To find:Based on the requirements choose the appropriate materials.Given data:A bar with a square…

Q: You have been asked to draw up a specification for a ceramic cladding tile that is likely to…

A:

Q: Define the term Modulus of Toughness?

A: Toughness is the property due to which the material can withstand impact loading without fracture…

Q: When a failure data set for spinel processed in a certain facility is analyzed, it is found that the…

A: Write the given data with suitable variables. σo=327 MPam1=8.75m2=6.25

Thermal Properties of Materials

In mechanical engineering, the thermal property is represented as the physical quantity that is relevant to the application of heat. The thermal properties are evaluated by variations in any specific material due to low heat or high heat. The quantities that influence the thermal property of the materials are mass, density, temperature, and many others.