A cylindrical rod 380 mm (15.0 in.) long and having a diameter of 10.0 mm (0.40 in.), is to be subjected to a tensile load. If the rod is to experience neither plastic deformation nor an elongation of more than 0.9 mm (0.035 in.) when the applied load is 24,500 N (5500 Ibf), which of the four metals or alloys listed in the following table is a possible candidate? Modulus Yield Tensile Material of Elasticity Strength Strength (MPa) (GPa) (МPа) Aluminum alloy 70 255 420 Brass alloy 100 345 420 Сopper 110 250 290 Steel alloy 207 450 550 O Steel alloy O Aluminum alloy O Copper O Brass alloy

A cylindrical rod 380 mm (15.0 in.) long and having a diameter of 10.0 mm (0.40 in.), is to be subjected to a tensile load. If the rod is to experience neither plastic deformation nor an elongation of more than 0.9 mm (0.035 in.) when the applied load is 24,500 N (5500 Ibf), which of the four metals or alloys listed in the following table is a possible candidate? Modulus Yield Tensile Material of Elasticity Strength Strength (MPa) (GPa) (МPа) Aluminum alloy 70 255 420 Brass alloy 100 345 420 Сopper 110 250 290 Steel alloy 207 450 550 O Steel alloy O Aluminum alloy O Copper O Brass alloy

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Please answer d,e,f
1. The tensile strength vs. temperature curves of aluminum are plotted below. Explain the meaning of these two curves. 400 Ultimate strength 300 Yield strength 200 100 -200 -150 -100 -50 50 100 150 200 250 Temperature, °C Strength, kPa
The wood beam has a cross section shown in figure. Determine the magnitude and location of the maximum tensile and compressive stress acting on the beam.
If a steel column with cross-sectional area A = 1000 mm^2 modulus of elasticity E = 200 MPa and length of 10 m is subjected to 2 kN axial tension, compute for its axial deformation
2. When a cylindrical body is subjected to uniaxial tensile force, which types of stresses are formed within the body? Show the locations of stresses on an appropriate sketch. 3. (a) If you were designing a metallic tool to be used at very low temperatures (negative temperatures), which material class would be the best option? (b) If you wanted to increase the strength of that tool for that very low temperature, which strengthening method would be the best option? Briefly explain your answer.
As shown in the figure below, a bronze bar is affixed between a steel bar and an aluminum bar. Axial loads are applied at the positions indicated. If the largest value of P that will not exceed an overall deformation of 4.0 mm, or the following stresses: 150 MPa in the steel, 130 MPa in the bronze, and 90 MPa in the aluminum, determine the stress in the bronze. Assume that the assembly is suitably braced to prevent buckling. Use Est = 200 GPa, Eal = 70 GPa, and Ebr = 83 GPa. (The correct answer is 71.36 MPa. Can you show the solution? Thank you!)
Please consider the given choices
A 3003-H14 aluminum alloy rod with 0.5 in. diameter is subjected to a 2000- lb tensile load. Calculate the resulting diameter of the rod. If the rod is sub- jected to a compressive load of 2000 lb, what will be the diameter of the rod? Assume that the modulus of elasticity is 10,000 ksi, Poisson’s ratio is 0.33, and the yield strength is 21 ksi.
#2 will upvote to anyone who will answer
A combined section of steel and copper is subjected to a compressive load. Refer to the table below for the properties of each Steel Copper Area, A 900 mm2 1,200 mm2 Modulus of elasticity, E 200 GPa 120 GPa Allowable compressive stress 140 MPa 70 MPa If the allowable strain for both materials is 0.0005, which of the following most nearly gives the maximum load the member can carry so that this allowable strain is not exceeded? Select the correct response 162.00 kN 185.00 kN 205.00 kN 175.00 kN
Design rod to support load of 175,000 pounds. What diameter rod is appropriate? Safety Factor, SF= Strength of Material (S)/ Applied Stress (sigma) = 1 Applied stress (sigma) = Force/Area Yield strength of Steel = 100,000 psi (yield means will undergo plastic deformation)
A steel bar 100 mm long is subjected to a tensile stress o. If change in length of bar is 0.05 mm what is the value of o? Given E = 200 GPa