A cylindrical container whose weight is titet Ibf is inverted and pressed into the water, as shown in the given figure. Determine the differential height h of the manometer and the force F needed to hold the container at the position shown. (specific weight of water is 62.22 lbf/ft³). 2).55 Manometer fluid Air S.G. = 2.1 d 9.84 in 7.87 in -hwter Water

A cylindrical container whose weight is titet Ibf is inverted and pressed into the water, as shown in the given figure. Determine the differential height h of the manometer and the force F needed to hold the container at the position shown. (specific weight of water is 62.22 lbf/ft³). 2).55 Manometer fluid Air S.G. = 2.1 d 9.84 in 7.87 in -hwter Water

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question 3:- A tank with 100.58 kPa pressure is connected with manometer to measure the pressure. The specific gravity of fluid was 0.85 and the atmospheric pressure is 96 kPa find the manometer column height "h". P = 96 kPa P=100.58 kPa h=? SG = 0.85
Closed valve -Air pressure = 16 psia 4 ft Air 2 ft Water Gage fluid (y = 90 lb/ft 3) Pressure gage Consider the tank in the figure above. Determine the pressure gage measurement. Assume a reasonable value of the specific weight for water at ambient temperature in Ib/ft
For the manometer shown, determine the difference in pressure between!
Q4/B/ Calculate the difference pressure (psf) between points A and B for the figure: 1000 mm Water 150 mm 700 mm Mercury (sg = 13.54) Oil (sg=0.86)
The cylinder shown in the figure extends 11 ft into the paper. If the cylinder has the radius of 4 ft, compute the vertical component of the hydrostatic force of the oil on the cylinder. 90 Oil (s.g. = 0.85) 4 ft 50
Answer in 3 significant figures..
A fluid compressed in a cylinder has a volume of 1000 (1liter) at 25 MPa and a volume of 900 at 3 MPa. compute the coetficient compressiblity. Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: MPan-1 Decimal Places required in the final answer: 2
Please show your solution on a paper with FBD
QLIn the figure given below calculate the of (H) for the given data: f1= di= L1= F2= D2= L2= QIL/s) 3.1 f1 di(mm) 55 L1(m) 16 f2 d2(mm) L2(m) 0.0193 0.021 72 20
A differential manometer is attached to a pipe as shown in figure below. Calculate the pressure difference between points A and B. (SG of Mercury = 13.6; SG of Oil = 0.95).
a manometer is a device that measures pressure. a common simple manometer consists of a U shaped tube of glass filled with some liquid. 1. the height of kerosene in the left leg was measured as 8.3 cm high and 5.2 cm on the right leg. yhe difference in elevation between the interfaces of kerosene and water measured 2.5cm. determine the specific gravity of kerosene.
Can you follow the instruction given: Determine the specific weight on each liquid by using the concept of P2 = P1+γh. Start with the upper most reader (Elevation 2m) since its P1 is zero. Repeat this until you reach the third elevation. Get the average of the three (3) specific weights. Divide this into the specific weight of water. Take this as your Specific Gravity for Fluid A. Gravity= 9.8 m/s2 The atmosphere is off in the simulation. These are the sample data given: