A cylindrical buoy 100mm in diameter and 120mm high is placed vertically inside the tank. The tank is 150mm in diameter and contains water 200mm deep and oil 30mm deep. If the buoy weighs 5N, determine the depth of the buoy submerged.

A cylindrical buoy 100mm in diameter and 120mm high is placed vertically inside the tank. The tank is 150mm in diameter and contains water 200mm deep and oil 30mm deep. If the buoy weighs 5N, determine the depth of the buoy submerged.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Water is flowing into a frustum of a conical vessel 2 m high at 100liters per minute. The vessel has…

A: To determine the height of water when the water surface is rising at 25.72 mm/min.

Q: What is the equivalent pressure head at the toe of the triangular dam in mm of Mercury? In meters of…

Q: A loaded scow has a draft of 1.80 meters in freshwater when erect. The scow is 6 meters wide and 12…

A: For stable condition BM>BC or GM>O .....1 GM=BM-BGBM=IminVfluid

Q: A discharge well that completely penetrates a confined aquifer has radius 0.5 m. The steadystate…

Q: A wooden cylinder (sg=0.61) is placed vertically in oil with specifc gravity of 0.85. Determine the…

A: The metacentric height (MB) =?

Q: For each of the three floating bodies, determine the buoyant force (kN) exerted by the liquid. Each…

A: Given Data Specific gravity of liquid = 0.8 Depth of submergence (h) = 1.5m Find Buoyant force…

Q: 1. A cylindrical buoy 1.35 m in diameter and 1.8 m high has a weight of 7500 N and its center of…

A: "since you have posted multiple questions with multiples subparts. We will solve first three…

Q: 5- Three smooth identical cylinders A, B and C stacked in a V-shaped trough as shown (weight 400 N…

A: Given :

Q: A new spar buoy, 0.5 m diameter, is being designed to carry oceanographic instrumen- tation in the…

A: It is possible that you may be startled to hear that our findings in the preceding example do not…

Q: A pipe has a total length of 9800 ft with diameter of 30 in., and its thickness is 5/8 in. Assume…

Q: problem 4 A vessel has two identical orifices A and B with identical values of C, provided on one of…

Q: A circular plate 5.01 m diameter is immersed in such a way that its greatest and least depth below…

A: Answer = e) none of the mentioned

Q: C hinge SALT WATER WATER 4m 60° A Gate 5m

A: Given Data:Specific Weight = 24kN/cu.mSGw=1.03Inclined Angle = 60°L=2.5m

Q: B 12 m No. 3 Please note, this is an Equilibrium problem. 8 m 10 m 1.2 m A O C 200kg P 2 m SAMPLE…

A: m=200kgtwo cables AB and ACFINDmagnitude of P and the tension in each cable

Q: Betermine the maximum height of a 3.5' wide by 3.5' long concrete block (y= 150 pcf) with a 2.5' X…

A: Unit weight of concrete = 150 pcf Unit weight of water = 62.43 pcf Let the height of the concrete…

Q: A conical funnel has radius 4 cm and height 8 cm. A liquid is draining from the funnel at a constant…

A: Draining rate (Q) = 1.3 cm3/sRadius of cone (R) = 4 cmHeight of cone (H) = 8 cm(a) Depth of the…

Q: 1.GIVEN: The vessel is initially full. Do = 200 mm C = 0.8 REQUIRED: Time to empty the vessel. 15 m.…

Q: A sphere 850mm-diameter floats half submerged in a tank of oil (sg=0.90) 4. What is the total…

Q: A hollow (open) hemispherical cup and a closed cylindrical buoy is floating in water as shown. The…

A: Draw the free body diagrams of both cup and cylinder. Note that since the hemisphere is hollow and…

Q: An upward flow of oil (mass density 800 kg/m°, dynamic viscosity 0.8 kg/m-s) takes place under…

A: Mass density of fluid (ρ) = 800 kg/m3 Dynamic viscosity (μ) = 0.8 kg/m-s Diameter of pipe (D) = 0.1…

Q: A cylindrical buoy 0.60 m in diameter and 1.80m high weighs 205kg. It is moored in salt water to a…

Q: Problem An open circular tank of 20 cm diameter and 100 cm long contains water upto a height of 60…

A: Given Diameter of cylinder D=20 cm, Hence, R=10 cm, Length L=100 cm, Height H=60cm, Speed N=300…

Q: An upward flow of oil (mass density 800 kg/m³, dynamic viscosity (0.8 kg/m-s) takes place under…

Q: An upward flow of oil (mass density 800 kg/m³, dynamic viscosity 0.8 kg/m-s) takes place under…

A: Given- Mass density = 800 kg/m3 Dynamic viscosity=0.8 kg/m-s Pressure at sections 1 and 2 are- 435…

Q: calculate the hydrostatic effect of the shaped 3M x 6m cover and the location of the thrust center…

Q: Fixed-Fixed bar was 20 centigrade degree at room temperature, Determine the thermal stress when the…

A: Given data: ΔT= 110-20= 90 oC α = 11.7 x 10-6 E = 200 GPa or 200 x 103N/mm2

Q: An upward flow of oil (mass density 800 kg/m³, dynamic viscosity (0.8 kg/m-s) takes place under…

A: Given data Density of oil = 800 kg/m3 Dynamic viscosity= 0.8 kg/ms Diameter of pipe (D) = 0.1 m…

Q: Consider the cross-section of the gravity concrete dam shown below. Check its stability against…

A: Above given data of dam we have to check its stability against overturning

Q: A cylindrical buoy 60 cm in diameter and 1.80 m high weighs 2810N. It is moored in salt water (s=…

A: Given data, D = 0.6m Specific weight of chain = 76.42 KN/m³ Chain weight = 117.7 N/m

Q: 5 kN/m A C 8 kN 0.5m 0.5m 2 m B.

A: in a given loaded beam it has been asked to determine the support reactions.

Q: A 100-N 8.0-m uniform cantilever is installed as a diving board fixed to the ground using two…

A: To determine the support reactions for a uniform cantilever. Given, Length of the cantilever = 8 m…

Q: A centrifugal water pump with a suction pipe is shown in Figure 3.5 Pump output is Q-0.03m'/s, the…

A: Apply Bernoullis theorem…

Q: Construct the active pressure diagram on plane XX and calculate the thrust P,. X 3m Pa=19 kN/m³ SP…

Q: An upward flow of oil (mass density 800 kg/m³, dynamic viscosity (0.8 kg/m-s) takes place under…

A: Solution: Given: mass density, ρ = 800 kg/m3 dynamic viscosity, μ = 0.8 kg/m-s pipe diameter, D =…

Q: tank contains ail sp. gr. 0.80, gasoline sp. gr. 0.90 and seawater sp. gr. 1.03. If the depths of…

Q: .) For the tank shown below (width = 1.25 m), determine (6.a) the maximum horizontal acceleration…

Question

A cylindrical buoy 100mm in diameter and
120mm high is placed vertically inside the
tank. The tank is 150mm in diameter and
contains water 200mm deep and oil 30mm
deep. If the buoy weighs 5N, determine the
depth of the buoy submerged.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given Data

VIEW

Step 2: Calculation

VIEW

Solution

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Water flows on a straight 350 m non-rigid pipe, 600 mm in diameter. The velocity of flow is 2.3 m/s. Pipe thickness is 18 mm. Bulk modulus of elasticity of water is 2.2 x 10° Pa. Modulus of elasticity of pipe material is 1.4 x 1011 Pa. What is the celerity of pressure wave in m/s? Select one: О а. 1,121 O b. 1,342 О с 1,202 O d. 1,421
m2
a) With the aid of neat sketehes, explain the stable conditions and unstable condition for a partially submerged object in a liquid column. b) A solid eylindrical pine wood (Specific gravity of 0.5) buoy has a cylindrical lead (Specific gravity of 11.3) weight attached as shown in Figure 1. i) Determine the equilibrium position (i.e. depth of immersion) of the buoy in seawater (Specific gravity of =1.03). ii) Caleulate the metacentric height. iii) Show that the buoy is stable. 4.88 m Pine wood 0.15 m -Lead Diameter (d) = 0.61 m nd Ixx. 64 Figure 1 Cylindrical buoy in sea water
Question A wooden block is form of a rectangular prism, floats with it's shortest axis vertical. The block is 40 cm long, 20 cm wide and 15 cm deep with a depth of immersion of 12 cm. Comment on the stability of the block.
Solve plz
A pontoon 6m x 6m x 3m floats in water with a draft of 2m. The orifice at the bottom of the pontoon is 160mm in diameter with a coefficient of discharge of C= 0.60. Determine the time required for the pontoon to sink its top after opening the orifice at the bottom.
A rectangular scow 10m wide, 5m high, and 12 m long has a draft of 3m. Its center of gravity is at the center of the scow. If the scow is tipped transversely until one side is just at the point of submergence, find the righting moment.subject : hydraulics
with FBD PLS...
Use SDM to analyze the following structure completely. 52 kN/m 15 kN Aci А 31 21 -4 m 3 m 1.5 m-
For each of the three floating bodies, determine the buoyant force exerted by the liquid. Each body has a draft(depth of submergence)of 1.5 m. SGliquid= 0.8.For the floating bodies in Problem 6(a)Which has the greatest amount of buoyant force?(b)Which has the least amount of buoyant force?
Please, Do not say: I cannot answer this problem.
Choose the correct answer