A cylinder is rotating about an axis that passes through the center of each circular end piece. The cylinder has a radius of 0.0600 m, an angular speed of 88.0 rad/s, and a moment of inertia of 0.850 kg • m. A brake shoe presses against the surface of the cylinder and applies a tangential frictional force to it. The frictional force reduces the angular speed of the cylinder by a factor of two during a time of 5.40 s. (a) Find the magnitude of the angular deceleration of the cylinder. rad/s2 (b) Find the magnitude of the force of friction applied by the brake shoe. Additional Matsal

A cylinder is rotating about an axis that passes through the center of each circular end piece. The cylinder has a radius of 0.0600 m, an angular speed of 88.0 rad/s, and a moment of inertia of 0.850 kg • m. A brake shoe presses against the surface of the cylinder and applies a tangential frictional force to it. The frictional force reduces the angular speed of the cylinder by a factor of two during a time of 5.40 s. (a) Find the magnitude of the angular deceleration of the cylinder. rad/s2 (b) Find the magnitude of the force of friction applied by the brake shoe. Additional Matsal

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

A piece of wood is pressed against a spindle sanding disk which is a uniform disk with a radius of 0.090 m, rotating at an initial angular velocity of 37.0 rad/s (ωi = 37.0 rad/s). This motion results in a constant tangential frictional force of magnitude f = 9.00 N and causes the sanding disk to come to a complete stop in = 25.0 s. (a) Small pieces of wood get removed from the large piece of wood with a speed equal in magnitude to the tangential velocity of the rim of the sanding disk (and in a direction tangent to the disk). What is thespeed of the pieces of wood when the disk is rotating at its initial angular velocity of ωi.(b) What is the angular acceleration α of the sanding disk.(c) How many revolutions does the disk complete before coming to a stop?
A playground merry-go-round of radius R = 2.00 m has a moment of inertia I = 250 kg · m2 and is rotating at 10.0 rev/min about a frictionless, vertical axle. Facing the axle, a 25.0-kg child hops onto the merry-go-round and manages to sit down on the edge. What is the new angular speed of the merry-go-round?
A thin rod has a length of 0.900 m and rotates in a circle on a frictionless tabletop. The axis is perpendicular to the length of the rod at one of its ends. The rod has an angular velocity of 0.607 rad/s and a moment of inertia of 1.06 x 10-3 kg-m². A bug standing on the axis decides to crawl out to the other end of the rod. When the bug (whose mass is 5 x 10-3 kg) gets where it's going, what is the change in the angular velocity of the rod? Number i Units
A uniform spherical shell of mass M = 6.0 kg and radius R = 18.0 cm rotates about a vertical axis on frictionless bearings (see the figure). A massless cord passes around the equator of the shell, over a pulley of rotational inertia I = 3.60×10-3 kg m2 and radius r = 6.0 cm, and its attached to a small object of mass m = 4.0 kg. There is no friction on the pulley's axle; the cord does not slip on the pulley. What is the speed of the object after it has fallen a distance h = 1.1 m from rest: Use work - energy considerations
A small object with mass 4.15 kg moves counterclockwise with constant angular speed 1.30 rad/s in a circle of radius 3.30 m centered at the origin. It starts at the point with position vector 3.301 m. Then it undergoes an angular displacement of 9.30 rad. (a) What is its new position vector? m (b) In what quadrant is the object located and what angle does its position vector make with the positive x-axis? ---Select--- ✓ at (c) What is its velocity? m/s (d) In what direction is it moving? (Give a negative angle.) • from the +x direction. (e) What is its acceleration? m/s² (f) What total force is exerted on the object? N
A small 0.340-kg object moves on a frictionless horizontal table in a circular path of radius 1.10 m. The angular speed is 7.09 rad/s. The object is attached to a string of negligible mass that passes through a small hole in the table at the center of the circle. Someone under the table begins to pull the string downward to make the circle smaller. If the string will tolerate a tension of no more than 108 N, what is the radius of the smallest possible circle on which the object can move? Number Units
A fixed pulley has a moment of inertia of 0.689 kg m² and a radius of 0.165 m. A string, wrapped tightly around the pulley, has a block of mass 0.409 kg attached to its free end. With the string vertical and taut, the block is carefully released so it can descend under the influence of gravity. As the block falls, the string unwinds and causes the pulley to rotate, but does not slip on the pulley. What is the speed of the block in m/s after it has fallen through 0.66 m? Express your answer to 2 decimal places.
When a diver gets into a tuck position by pulling in her arms and legs, she increases her angular speed. Before she goes into the tuck position, her angular velocity is 5.5 rad/s, and she has a moment of inertia of 1.6 kg · m2. Once she gets into the tuck position, her angular speed is 19.3 rad/s. Determine her moment of inertia, in kg · m2, when she is in the tuck position. Assume the net torque on her is zero.
A uniform disk (1=1/2 mR2) has a mass of 3 kg and a radius of 2m. The disk is mounted on frictionless bearings and is used as a turntable. The turntable is initially rotating at 120 rpm (revolutions per minute, convert it to rad/s). A hollow cylinder has the same mass and radius as the disk. It is released from rest, just above the turntable, and on the same vertical axis. The hollow cylinder slips on the turntable for 0.20 s until it acquires the same final angular velocity as the turntable. (HINT: Note that some of the information given is not needed! Think which conservation law(s) apply.) The final angular momentum of the system is closest to: L = Submit [5] ΑΣΦ Request Answer ? kg. m²/s 4
When a diver gets into a tuck position by pulling in her arms and legs, she increases her angular speed. Before she goes into the tuck position, her angular velocity is 5.5 rad/s, and she has a moment of inertia of 2.1 kg · m2. Once she gets into the tuck position, her angular speed is 11.7 rad/s. Determine her moment of inertia, in kg · m2, when she is in the tuck position. Assume the net torque on her is zero. kg · m2
A cylinder is rotating about an axis that passes through the center of each circular end piece. The cylinder has a radius of 0.110 m, an angular speed of 64.0 rad/s, and a moment of inertia of 1.08 kg-m². A brake shoe presses against the surface of the cylinder and applies a tangential frictional force to it. The frictional force reduces the angular speed of the cylinder by a factor of 9 during a time of 8.00 s. (a) Find the magnitude of the angular deceleration of the cylinder. (b) Find the magnitude of the force of friction applied by the brake shoe. (a) Number i (b) Number i Units Units
A student sits on a rotating stoll holding two 8.0kg objects. When his arms are extended horizontally, the objects are 1.3m from the axis rotation and he rotated with an angular speed of 1.8rad/s. The moment of intertidal of the student plus stoll is 4.5kg•m^2 and is assumed to be constant. if the student pulls in the two objects horizontally to 0.50m from the rotation axis. What is the new angular speed in rad/s of the student? (3 sig fig)