A cylinder is made of steel plate is intended to be used as a container for compressed air. The dimensions of the cylinder are L=2m, D=60cm, and t = 0.005m. If the ultimate tensile stress of the steel is 400 N/mm², Young's modulus is 200000 MPa and Poisson's ratio is 0.25. 1- Determine the maximum air pressure that can be stored in the cylinder (use factor of safety = 2) 2- Determine the change in the volume of the cylinder due to storing maximum pressure.

A cylinder is made of steel plate is intended to be used as a container for compressed air. The dimensions of the cylinder are L=2m, D=60cm, and t = 0.005m. If the ultimate tensile stress of the steel is 400 N/mm², Young's modulus is 200000 MPa and Poisson's ratio is 0.25. 1- Determine the maximum air pressure that can be stored in the cylinder (use factor of safety = 2) 2- Determine the change in the volume of the cylinder due to storing maximum pressure.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The rigid bar of negligible weight is supported as shown in the figure. If W=80 kN, compute the temperature change of the assembly that will cause a tensile stress of 50 MPa in the steel rod. Use the following data:
Solution w/FBD
Determine the compressive force (in lb) in the bars shown after a temperature rise of 173°F if d = 0.015 in. Round off the final answer to five decimal places. Use the following data: Bronze Aluminum A = 2.24 sq. in A = 2.78 sq. in E = 14959726 psi E = 10594540 psi L = 12.5 in L = 16.6 in α = 11.61 x 10-6/ °F α = 12.67 x 10-6/°F
An SSTM A36 strucural steel beam 3.6 m long is placed between two rigid supports when the temperature is 15 0C. What is the stress developed in the beam if the temperature rises to 50 0C? ___ MPa. Assume that the proportional limit is 235 MPa, and that lateral buckling is prevented. Calculate your answer to 1 decimal place.
A rigid bar of negligible weight is supported and loaded with 70 kN, compute the temperature change AT (°C) that will cause the stress in the bronze rod (L = 1.5 m, A = 300 mm?, and E = 83 GPa) to be 50 MPa. Assume a = 18.9 µm/(m°C) for bronze and 12.8 um/(m°C) for aluminum (L = 3 m, A = 750 mm2, and E = 70 GPa). Aluminum Bronze 2.5 m 1.5 m 70 kN
(a) 128.5 GPa circular rod of diameter 30 mm and length 200 mm is subjected to a tensile force. The axtension of rod is 0.09 mm and change in diameter is 0.0045 mm. What is the Poisson's ratio of the material of the rod? (a) 0.35 (b) 0.33 (c) 0.32 (d) 0.30
Problem: A steel rod with a cross-sectional area of 180 mm2² is stretched between two fixed points. The tensile load at 25°C is 3,600N. Assume thermal coefficient equal to 11.7 x 106 mm/ (mm°C) and E= 200 GPa. a. What is the temperature at which the stress will be zero? b. What is tthe temperature at which the compressive stress will be 48 MPa?
A cantilever beam with cross section shown below and span of 3 m is subjected to concentrated load (P) at the free end. If the maximum allowable tensile stress equals to 10 MPa what is the maximum value of the load P can be applied.
2. Given a 5 mm diameter steel wire, which is 4 meters long, carries an axial tensile load P. Find the maximum safe value of P if the deformation of the wire is limited to 5.5 mm and the allowable normal stress of the wire is 280 MPa. Use 200 000 MPa for the modulus of elasticity of steel.
A tapered steel bar of length 2m is subjected to an axial load of 20kN. Take modulus of steel as 200GPa. What is the strain produced in the bar? (in 10-5) = 100 mm 2m >= 50 mm 20000 N
Q.3 The compressive strength of (Ø25×25) cm cylinder is 30 MPa at an age of 21-day, determine the direct tensile strength at the age of 7-day.