A cyclist on a circular track of radius r = 800 feet is traveling at 27 ft s^-1. His speed in the tangential direction increases at the rate of 3 ft s^-2. What is the cyclist's total acceleration? 2.8 ft s^-2 -3.12 ft S-2 -5.1 ft s^-2 3.13 ft s^-2 None of the choices

A cyclist on a circular track of radius r = 800 feet is traveling at 27 ft s^-1. His speed in the tangential direction increases at the rate of 3 ft s^-2. What is the cyclist's total acceleration? 2.8 ft s^-2 -3.12 ft S-2 -5.1 ft s^-2 3.13 ft s^-2 None of the choices

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Solve the Given DE via Variable Separable
90 MPa 55 MPa 70 MPa 70 MPa 55 MPa -90 MPa 65° The state of stress on an element relative to the xy-axis is presented above. The element is to be reoriented as shown. a) What are the components that describe its original state of stress (x, y, Txy) and what is the angle of rotation (0)? Make sure your signs are correct. b) Using the equations of stress transformation, determine x, y, and Txy and draw these components of stress on the rotated element. c) What are the principal stresses and angles of the principal planes? What is the shear stress associated with this orientation? d) What is the maximum in-plane shear stress and the angle of its associated plane? What are the associated normal stresses in this orientation? e) What is the absolute maximum shear stress and what plane (xy, xz, or yz) does this stress act upon?
A truss (Truss) is subjected to force as shown in the figure below. Try to calculate the vertical displacement of point C. A of all rod frame sections is 200 mm^2 and E is 200 GPa, both of which are constants.
In your words, discuss the strengths and limitations of the Bishop’s (1959) equation.
Concretes have several properties. Which one of the following statements is incorrect? a. Concretes have good tensile strength b. Concretes have good shear strength c. Concretes have good compressive strength d. Concretes have good wear resistance
Mechanics Of solids.
1. Element A is subjected to the stress state shown in the x-y plane 75 MPa (+x is to the right, +y is up). Use Mohr's Circle to solve the following problems. You MUST draw Mohr's Circle to get credit for these problems! 25 MPa 105 MPa (a) Determine the complete state of stress on the element in the x-y coordinate system. (b) Determine the state of stress if this element is rotated 25° (c) Determine the values of the principal stresses. (d) Determine the value of the maximum in-plane shear stress, Tmax in plans. (e) Determine the absolute maximum shear stress, Tmax abzolute (by drawing circles from each principal stress to the origin). Is Tmax abzoluts in the x-y plane (i.e., is Tmax absolute equal to Tmax, in-plane)? nswers: (a) ox = 105 MPa (T); oy = 75 MPa (T); Ty = +25 MPa; o; = Tx = Tyz = 0 (b) ox = 118.8 MPa (T); o, = 61.21 MPa (T); t = -4.579 MPa (c) 01.2 =119.2 MPa (T), 60.8 MPa (T) (d) Tmax in-plane = 29.15 MPa (e) Tmax absolute = 59.58 MPa; no, Tmax, absolute is not in the…
Determine the z-coordinate of the mass center of the homogeneous paraboloid of revolution shown. Answer: Z = i 3 in. 11 in. --y in.
Develop a finite element model to solve the displacement at the point where the 10000 N is applied (50 cm from the right end). E=20(10°) N/cm² A=8 cm? A=4 cm? 10000 N 3 -75 cm- -50 cm-
The answers are on the right but I cannot do the solutions. Can you help me? The 8-element lattice system structure in the figure was loaded from point F with a load of 100 NDetermine the zero bars and the load value to which each element is subjected.Indicate whether the elements are under tension or pressure.
Consider the s single degree of freedom presented in the figure Тol Base The transformation of the first frame relative to the base is
Find the centre of mass of the 2D shape bounded by the lines y = ±1.3x between x = 0 to 2.1. Assume the density is uniform with the value: 3.5kg. m-2 Also find the centre of mass of the 3D volume created by rotating the same lines about the x-axis. The density is uniform with the value: 1.9kg. m (Give all your answers rounded to 3 significant figures.) a) Enter the mass (kg) of the 2D plate: Enter the Moment (kg.m) of the 2D plate about the y-axis: Enter the x-coordinate (m) of the centre of mass of the 2D plate: S Enter the mass (kg) of the 3D body: Enter the Moment (kg.m) of the 3D body about the y-axis: Enter the x-coordinate (m) of the centre of mass of the 3D body: a ed db) ks 10