A cross-section of a concrete gravity dam is show in figure. Analyze the stability of the block for full and empty upstream reservoir cases, separately. Ignore earthquake, silt, and ice forces. Specific weights of concrete and water are 23kN m' and 10 kN m', respectively. Compressive and shear strengths of concrete are 35 MPa and 6 MPa, respectively. The coefficient of friction between block and foundation is 0.65. There is no tailwater in the downstream. Require safety factors can be taken as those of usual loading. 4 m 12 m 1H:4V 1H:12V t--

A cross-section of a concrete gravity dam is show in figure. Analyze the stability of the block for full and empty upstream reservoir cases, separately. Ignore earthquake, silt, and ice forces. Specific weights of concrete and water are 23kN m' and 10 kN m', respectively. Compressive and shear strengths of concrete are 35 MPa and 6 MPa, respectively. The coefficient of friction between block and foundation is 0.65. There is no tailwater in the downstream. Require safety factors can be taken as those of usual loading. 4 m 12 m 1H:4V 1H:12V t--

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Civil engineering -Hydraulics
An engineer proposes as a solution to the problem of the dam, to reinforce it according to the figure shown, but now the critical height h of the water level must be determined, which would make the indicated concrete reinforcement on the verge of overturning due to the water pressure. The density of the concrete 2.40 Mg/m^3, H=18m and d= 6m. Hints: use typical values of water, consider one meter width of the dam to then generalize and don't forget point A.
For the below wooden beam, under the given loading and dimensions: 50 kN C 4m w = 10 kN/m Calculate and sketch the maximal normal stress at point C. B 150 mmm 360 mmm
For linear stress variation over the base of the dam of the figure, find where the resultant crosses the base and compute the maximum and minimum pressure intensity at the base. Neglect hydrostatic uplift. Ans.Pmax=555 kPa; Pmin=129 kPa Note: unit weight of concrete is 2.5 times unit weight of water. 6m 19m 1 Y'=2.5Y 1 30 40 ¹3 mi 4 m -11 m
NOTE: ANSWER SHOULD BE ON THE CHOICES
17. A cast-iron pipe of 750 mm diameter is used to carry water under a head of 60 m. What is the approximate thickness of the pipe if permissible stress is to be 20 MPa? (Take specific weight of water as 9.81 kN/m³) (a) 22 mm (c) 11 mm (b) 14 mm (d) 7 mm
Civil engineering -Hydraulics
The soil profile at a road construction site is as shown in figure (not to scale). A large embankment is to be constructed at the site. The ground water table (GWT) is located at the surface of the clay layers, and the capillary rise in the sandy soil is negligible. The effective stress at the middle of the clay layer after the application of the embankment loading is 180 kN/m². Take unit weight of water, Yw = 9.81 kN/m3. Embankment load boudi Sand GWT 2m y = 18.5 kN° it enit Clay Specific gravity, G̟ = 2.65 Water content, w = 45% Compession index, C. = 0.25 6m %3D %3D Impermeable layer The primary consolidation settlement (in m, round off to two decimal places) of the clay layer resulting from this loading will be
A concrete dam retaining water is shown. If the specific weight of the concrete is 23.54 kN/m3, find the maximum pressure on the base. Assume there is no hydrostatic uplift and that the coefficient of friction between dam and foundation soil is 0.48. Y = 5.6 m B = 3.2 m W = 1.6 h = 4.8
Solve this.
A rectangular reinforced concrete beam with width of 250mm and effective depth of 500mm Is subjected to 150kNm. The beam is reinforced with 4 – 25mm bars. Use n = 9 Kindly answer all of the said questions, thank you!
Calculate the total stress in the given beam due to prestress only. A rectangular beam 200 x 300 mm is prestressed with 15-6 mm diameter wires located at 65 mm from the beam soffit and 2-6 mm diameter wires located 25 mm from the top of the beam. The prestress is 1000 MPa with a length of 8 meters.