1,0 m * 4 m * 5 m TINININININININ NINI NININIK Dry bark clay y =18 kN/m³ PVP V I 1 I I Sa Ysat =15 kN/m³ SiMr Ysat 21 kN/m³ ㅅ ㅅ ㅅ ㅅ ㅅ ㅅ K K ㅅㅅ Review level

Q: For question 103A and 103B, the thin-walled cylindrical container shown below. Say p is the internal…

A:

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods as shown. The…

A:

Q: 3- Check the equilibrium of the material in the absence of body forces for the stress components in…

A:

Q: Determine the principal stresses, the maximum in-plane shear stress, and average normal stress.…

A:

Q: 30° 0.75 in.

A:

Q: 10 MPа 4 ksi 10 MPа 4 ksi 10 MPа 2 ksi

A: Solution:- 1. Radius of Mohr's circle: r=σx-σy22+τxy2  =10-1002+0  =0 2. Radius of Mohr's circle:…

Q: ults in a differential element at the poin a a 0.5 m

A:

Q: Determine stress in portion CD, BC, and in AB

A: FBD : For portion CD: For portion BC : Force in BC Portion=-45+30=-15 kips For portion CD : Force…

Q: The normal and shear stresses acting on element A are 6,650 psi, 17,600 psi, and 2,700 psi (see part…

A:

Q: Please answer the ELONGATION OF BAR A IN mm and AXIAL STRESS DEVELOPE IN C IN MPa. Rate will be…

A:

Q: -termine the principal stresses, the maximum in plane d average normal stress. Specify the…

A: Since this a multiple question as per Bartleby policy, we can answer only first question, for other…

Q: The rod has a diameter of 40 mm. Determine the state of stress at point A and draw the resulting 3-D…

A:

Q: Required information Consider the given state of stress. Take A = 16 MPa and B= 48 MPa. B 60 MPa

A: Given: σx=16 MPaσy=-48 MPaτxy=60 MPa

Q: At a point in a component, the state of stress is shown on the element below. Assume that the stress…

A:

Q: I jp. sin. 05 in. B. 3 kip A9 kip 8 kip Lc-2 kip

A:

Q: - 150 mm - 3 mm B 200 mm A 3 mm

A: shear strain  is defined as the angular deformation of the object when subjected to  shear force…

Q: Determine maximum shear stress if maximum principal stress is 10 Mpa and minimum principal stress is…

A:

Q: ! Required information Consider the given state of stress. Take A= 16 MPa and B= 55 MPa. B 60 MPa…

A:

Q: At a point in a component, the state of stress is shown on the element below. Assume that the stress…

A: Determine the magnitude of the absolute maximum shear stress that acts at the point.

Q: The major and minor principal stresses acting at a point in a stressed material are 80 psi…

A: Major Principal stress, σ1=-80 psi (compression) Minor Principal stress, σ2=20 psi (Tension) (a)-…

Q: Question 2. Determine the principal stress, the maximum in-plane shear stress, and average normal…

A:

Q: 2. A cantilever beam of 1.0 m long is subjected to a concentrated load Po at its free end. Determine…

A: given: allowable  tensile stress=180MPa allowable compressive stress=140MPa allowable shear…

Q: Y For point A and in x-y plane, the value of major principal stress in (MPa) is X Z A Dia = 10 mm T…

A:

Q: Determine maximum and minimum principal stress

A: Given data : Normal stress along X axis (σX)=-560 MPaNormal stress along y axis (σY)= 250 MPaShear…

Q: Rev Part C-Orientation of the element subjected to maximum shear stress on its sides Determine the…

A:

Q: Solve this early all subparts B) determine the principal plane (for σmax) in radians. C) Determine…

A:

Q: Knowing that the maximum allowable stress is 43 MPa, determine the magnitude of the largest moment…

A: A beam of T-section is subjected to bending

Q: ince P = 10 kN in the welded annex given in the figure, a) Write the equation for the neutral axis…

A: to find normal stress distribution

Q: 3 ksi S ksi iven the state of stress above (ignore 70° plane): calculate the maximum she ress,…

A: To find maximum shear and principal stress

Q: Q: For the state of stress shown in fig. below. Determine the principle stress and the max. shearing…

A: given  fig  sigma x  sigma y shear stress  to find  max shear stress principle stress]

Q: Find stress Force 1 N Cross sectional Area=0.2 mm2

A: Introduction : The given question is related to solid mechanics . In this question we are provided…

Q: 2. For the given state of stress shown in figure 2. + 48 MPa Figure 2. a. Construct Mohr's circle…

A: The principal planes are those on which only the normal stresses act with the shear stress zero. The…

Q: A Plane stress state is given on a material element as shown below. O=a+b+h (MPa), Oz=b+c+d+h (MPa),…

A:

Q: Assume the sections have cracked and use the transformed-area method to compute their flexural…

A: Given:- The area of steel reinforcement provided = 4-20 mm  The magnitude of the moment = 90 kN-m…

Q: Knowing that the couple shown acts in a vertical plane, determine the stress at (a) point A, (b)…

A: Given, A cantilever beam, Bending Moment = M = 12kNm(clockwise) Find out , Stress at point A and B?…

Q: ProbleT --- An aluminum bar has diameter d = 40 mm, shear modulus of elasticity G = 27 GPa, and…

A: Simple stress is expressed as σ=PA, it is force per unit area. Shear stress is developed is applied…

Q: The plate of thickness, t 5 mm, is loaded with the following stress; o, = 100 MPa, o, = -60 MPa, E =…

A:

Pricing Excavation and Backfill

Backfill, in construction, is the activity of returning the soil and gravel that are removed during building construction or using them again to toughen and support the foundation of the building or any other structural component.