A crest and sag curve connect a 0% west highway segment (left) with a +1.50% east highway segment (right). The 0% west highway segment is at a higher elevation than the start of the +1.50% east highway segment. The two vertical curves connect with each other (PVT = PVC) and share a 1.9% (use -1.9% for calculation) common grade. If the design speed of the curves is 65 mi/h. What is the elevation difference (ft, use format 0.00, range is +/-0.03) between the two road segments?

A crest and sag curve connect a 0% west highway segment (left) with a +1.50% east highway segment (right). The 0% west highway segment is at a higher elevation than the start of the +1.50% east highway segment. The two vertical curves connect with each other (PVT = PVC) and share a 1.9% (use -1.9% for calculation) common grade. If the design speed of the curves is 65 mi/h. What is the elevation difference (ft, use format 0.00, range is +/-0.03) between the two road segments?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An engineer has been decided to design a vertical curve of a (- 2.5) percent grade meting a (3.2) percent grade, if the design speed (45) mile/ hr., (Use f Skidding = 0.3, t = 2.5 Sec., K=100). The minimum length of the Curve that will be satisfying all criteria is: * 0:07
1) An equal-tangent crest vertical curve has a 50 mi/h design speed. The initial grade is +3%. The high point is at station 33+37.43 and the PVT is at station 37+18.26. What is the elevation difference between the high point and the PVT? 2) A 1400-ft-long sag vertical curve (equal tangent) has a PVC at stateion 115+00 and elevation 750ft. The intial grade is -3.5% and the final grade is +6.5%. Determine the elevation and stationing of the low point, PVI, and PVT. If you could show as many steps taken as possible that would be helpful in me actually understanding how to do the problem. Thanks
A 777m equal tangent crest vertical curve has PVC at Sta 16+430 and at elevation 115m. The initial grade is 7.9% and the final grade is -3.3%. Determine the elevation (m) of PVT.
Determine the minimum length of a sag vertical curve between a -1.06% grade and + 2.1% for a road with 110 kph design speed. The vertical curve must provide 200 m sight distance
answer question 25 only
Two sections of a highway are separated by 800m. The initial grade is +3.0% and the final grade is -1.0% and the elevation is 12m. Determine the curve lengths required for a 120km/hr vertical alignment to connect two highway segments, keeping the connecting grade as small as possible.
Q\ on a certain highway section, a +2% grade meets a -8% at a point with an elevation of 50m. The symmetrical parabolic curve joining the two grades provide a safe driving speed of 120 km\hr. determine the elevation of the highest point on the pavement surface within this section? in Assume a=3.41lm\sec² , S
An equal tangent vertical curve is intended to connect grades of 3.5% and -2.9%. If this curve is to be a part of a highway designed with a PSD of 500ft, determine the minimum length (ft) of the vertical curve. Use exact solution (do not use the table).
A crest vertical curve will connect a 1.5% grade to a -3% grade with a design speed of 45 mph. Using the SSD (stopping site distance) criterion, what is the minimum length of the curve?
A new highway is designed to join a crest curve with +1.0% and -0.5% grades for PVC and PVT, respectively. Knowing that the stations of PVC and PVI are STA 51+25 and STA 56+90, examine whether or not the curve is long enough to provide passing sight distance when the design speed is 60mi/h.
3.7 An equal-tangent crest vertical curve is designed for 65 mi/h. The initial grade is +3.4% and the final grade is negative. What is the elevation difference between the PVC and the high point of the curve?