A crate is sitting in the center of a flatbed truck. The truck accelerates to the left, and the crate moves with it, not sliding at all. What is the direction of the frictional force exerted by the truck on the crate? * O To the right No frictional force because the cra is not sliding. O To the left O None of these

A crate is sitting in the center of a flatbed truck. The truck accelerates to the left, and the crate moves with it, not sliding at all. What is the direction of the frictional force exerted by the truck on the crate? * O To the right No frictional force because the cra is not sliding. O To the left O None of these

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Teemo is trying to move the crate weighing 15 kN by pulling on the rope at an angle 0 to the horizontal. T. 11. Find the smallest possible force that Teemo should pull to cause the crate to slide. Coefficient of static friction is 0.25. 12. Determine the angle 0. 13. Determine the horizontal frictional force acting at the bottom of the crate. 14. Determine the angle of static friction? 15. If Teemo pulls the crate at the force 5kN, will the crate move? (Prove your answer mathematically)
2. Block B has a mass, mb, and is supported as shown. What is the maximum value of mb that can be lifted under force P = 300 lb applied to block A as shown? The static coefficient of friction on all surfaces is 0.2.
1. Consider a water jet having a diameter of D = 1 cm and a flow of Q = 1 L/s. The jet is deflected by a fixed plate which is inclined at an angle of 50° from horizontal. a) Determine the velocity vx in the x-direction in m/s. b) Determine the velocity vy in the y-direction in m/s. c) Determine the resultant force Fx on the plate in the x-direction in N. d) Determine the resultant force Fy on the plate in the y-direction in N. e) Determine the combined resultant force F on the plate in N. 1 L/s 50° V = 6 m/s
An experimental device imparts a force of magni tude F = 225 N to the front edge of the rim at A to simulate the effect of a slam dunk. Determine the moments of the force F about point 0 and about point B. Finally, locate, from the base at 0, a point C on the ground where the force imparts zero moment.
The 58 kg uniform beam (slender rod) is lying on the floor when the man exerts a force of F = 336 N on the rope, which passes over a small smooth peg at C. a) Determine the initial angular acceleration of the beam, in rad/s2. b) Find the horizontal reaction on the beam at A (considered to be a pin) at this instant. Express your answer in Newtons.
Beam AC is in equilibrium with loading 100 N at B shown in the figure when β = 45. Determine the unknown forces Ax and Ay at A in x and y direction and Rc perpendicular to the beam AC in y’ direction at C by using the equilibrium equations: ∑ ???= 0 ; ∑ ??y= 0; and ∑ ???= 0 where o is an arbitrary point. (you have three equations to solve three unknowns)
If the vertical component of the force F applied to the ring is 10 lb, determine the magnitude F and also the horizontal component. F 300
Q/ An overhanging beam is subjected to the combined loading shown in Figure below. Determine the slope at support 4 and the deflection at C. 50 KN 25 kN/m 50 kN C D m www 5m 5m 4 m
The three identical bars, each weighing 10.8 lb, are connected by the two freely pinned links of negligible weight and are resting on a smooth horizontal surface. Calculate the initial acceleration a of the center of the middle bar when the 7.8-lb force is applied to the connecting link as shown. 7.8 lb Answer: a = i ft/sec2
The simply supported beam is made of A-36 steel and is subjected to the loading shown in Figure Calculate the deflection at its center C using the virtual work method. Figure 60 kN 75 kN m A C 4 m 4 m B.
The 700-N force is applied to the 100-kg block, which is stationary before the force is applied. Determine the following: 1. magnitude of the friction force F exerted by the horizontal surface on the block 2. direction of the friction force F exerted by the horizontal surface on the block 3. If P is unknown, determine the largest force P that can be applied without causing the block to slide to the right. P = 700 N 100 kg 30° H = 0.80 %3D Hp = 0.60 %3D 4.
The three identical bars, each weighing 6.1 lb, are connected by the two freely pinned links of negligible weight and are resting on a smooth horizontal surface. Calculate the initial acceleration a of the center of the middle bar when the 5.7-lb force is applied to the connecting link as shown. # Answer: a = i 5.7 lb ft/sec²