A coupling with material AISI C1045 as rolled transmits 65.5 HP at 1750 rpm. The material of the 1.75 inch shaft... iş also AISI C1045 as rolled and the key is cold drawn AISI C1020. N= 2.5. Determine the following: 1. Size of bolt (dia.) if there are 6 bolts made of AISI C1045 as rolled at a bolt circle of 5 inches. Note: Select standard bolt diameter from AT14 of DOME by Faires (see Lecture on fasteners for this Table) Calculated Dia: Standard Size to use: 2. Required b and t if a flat or rectangular key is used: Answer: 3. Required length of key, if a flat or rectangular key is used: Note: Calculate for two type of stresses on key, then select your answer. Length Based on shear length Based on compression: Length to use: 4. Required if a square key is used: Answer: 5. Required length of key, if a square key is used: Note: Calculate for two type of stresses on key, then select your answer. Length Based on shear length Based on compression: Length to use:

A coupling with material AISI C1045 as rolled transmits 65.5 HP at 1750 rpm. The material of the 1.75 inch shaft... iş also AISI C1045 as rolled and the key is cold drawn AISI C1020. N= 2.5. Determine the following: 1. Size of bolt (dia.) if there are 6 bolts made of AISI C1045 as rolled at a bolt circle of 5 inches. Note: Select standard bolt diameter from AT14 of DOME by Faires (see Lecture on fasteners for this Table) Calculated Dia: Standard Size to use: 2. Required b and t if a flat or rectangular key is used: Answer: 3. Required length of key, if a flat or rectangular key is used: Note: Calculate for two type of stresses on key, then select your answer. Length Based on shear length Based on compression: Length to use: 4. Required if a square key is used: Answer: 5. Required length of key, if a square key is used: Note: Calculate for two type of stresses on key, then select your answer. Length Based on shear length Based on compression: Length to use:

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. A inotor carrying XI-4. In a brick-making machine is found this train of gears. pulley E, which is 6 in. in diameter, drives the machine. The wide-faced roller F, 12 in. in diameter, drives a conveyor belt. If the motor runs at 1200 rpm, what is the speed of the conveyor belt in feet per minute? (Neglect the thickness of the belt.) 12 T. 144 12 T 27 T. 108 T 48 Dia, PROB. XI-4 (proved that answer is 17. ft/_)
Derive the expressions for A, B, & C in the given figure with the help of clear drawing and stepwise procedure. Also find the expression for the Length of the belt drives for open and closed belt drives.
The questions is this: A 5000-lb. gear box is provided with a steel (as rolled B1113) eyebolt for use in moving it. What size bolt should be used: a.if UNC threads are used? b.If UNF threads are used? c.If the 8-thread series is used? and I got the answer in the picture provided. Can you explain further the basis of the choice of the design factor?
Driver Pulley 1 is 10” in diameter, runs at 1200 RPM, and supplies 2.5 ft-lbs of torque. Pulley 2 (driven) is 32” in diameter. What is the output torque of Pulley 2? What is the output speed of Pulley 2?
Please summarise the answers for this question for i and ii as it looks too long
3. A 15/16 in. wide key has depth of 5/8 in. It is 12 inches long and is to be used on a 200 hp, 1160 rpm, squirrel-cage induction motor. The shaft diameter of 3 7/8 inches. The maximum running torque is 200% of the full-load torque. Compute the maximum torque.
1. The dimensions for the shaft size are o 10-0 +0.068 +0.01 ф10+0041 mm and the hole size are +0.005 mm. Find the maximum and minimum limits of hole and shaft. Find the tolerance for hole and shaft. Also find the type of fit.
An epicyclic gear in figure 1 consists of ring gear, planet gear and sun gear. The ring gear has 72 internal teeth and sun gear has 32 external teeth. Planet gear meshes with both ring and sun gears and is carried on an arm which rotates about the Centre of the ring gear at 20 rpm. If the gear A is fixed, Calculate the speed of planet gear.
can you please find the solution question no:27
Must solve all three questions. Dont say i will solve only one.
What is the LMC of shaft C?
Problem number 10 only. Thank you so much!