A control system has the following systems in the forward loop; s2(s+1)2 and (s+2)/s*(s+1). The output of the system is fedback to the input using the following feeddback path; (2s+3)/s Determine the type of the system. 3 O.2 01 Cannot be determined

A control system has the following systems in the forward loop; s2(s+1)2 and (s+2)/s*(s+1). The output of the system is fedback to the input using the following feeddback path; (2s+3)/s Determine the type of the system. 3 O.2 01 Cannot be determined

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Please answer this,I want a detailed explanation. An a.c. supply drives a half-controlled thyristor bridge with a resistive load. Sketch the circuit diagram, and the voltage and current waveforms.
Explain dual slope ADC and successive approximation ADC with neat block diagram and compare the two approaches
Parallel clipper circuit is given in the figure. Input voltage , Vs= 10 V. Find the voltages obtained on R1, RL and diode. (Note: Take the voltage amplitude as +10, -10V. Take the division value per oscilloscope screen as 5 ms. You can get the function generator frequency value as 50 or 100 Hz.) R-200 20 R |2 2K0 201
Question 14 In the given circuit, a step down transformer with an RMS voltage as 110V / 11-0-11 V is used with RL = 1 KQ. Not yet answered Assume diode as Germanium and the input frequency is F= 50HZ. Marked out of Dy 3.00 P Flag question RL D, 1- Name the given circuit . 2- Find The PIV. 3- Find Current trough load resistance. 4- Draw the Input and Output wave forms. B I 00000
Determine zener diode boltahe value as well as the ripple percentage of the circuit bellow with 240Vpp
Question Distinguish between combinational and sequential circuits
With the input vm =66 volts, determine wm ở in rad/s at time t -4.2 sec? Vin ea R2 DC MOTOR Tm, Wn, Om Jm =0.17 kg-m2, Dm =0.039 N-m-s/r, Km =0 N-m/r, R2 =2.4R1, L. = 0 T. = -0.017wm +3.69 N-m for e, =89 volt.
A resistor and a capacitor are connected in series across a supply of 250 Volts. When the supply frequency is 50 hz and the current in the circuit is 5 A. When the supply frequency is 60 hz, the current is 5.8 A. find C.
1- spark gaps testing method is applicable for testing 2- the electrical circuit that we use to measure high voltages and is not affected by frequency change 3- We can say high voltages if exceed ------------ V (Alternating voltages) 4- Transient voltages which are caused over voltages be in two forms 5- High voltages can be generated for testing in three ways ------
With the input Vin =31 volts, determine wm = ở in rad/s at time t =2.2 sec? Vin ea DC MOTOR Tm, Wm, Om Jm =0.22 kg-m2, Dm =0.049 N-m-s/r, Km =0N-m/r, R2 =1.5R1, La = 0 Tm = -0.016wm+3.11 N-m for ea =82 volt.
A chopper circuit works at a frequency of 4 kHz of a 220 V dc supply. For 180 V output voltage, find the conduction and blocking periods of a thyristor in each cycle. Select one: a. 0.209 ms, 0.234 ms b. 0.404 ms, 0.055 ms c. 0.204 ms, 0.045 ms d. 0.704 ms, 0.897 ms
A charging circuit that will deliver constant DC current will be designed. The input of the circuit is 220V / 50Hz AC and its outputIt will be 5V / 2A DC.The circuit will consist of 3 parts:AC transformer will reduce the voltage on the inputii. AC rectifier circuit will convert low AC voltage to DCiii. Current source, this part will keep the current at the output constant.You determine the transformer drop rate in the first part. Its output is low voltage ACas the source and design the second and third parts accordingly.