A continuous wood stave pipe is 3.0 m in diameter and is in service under a head of 30.0 m of water. The staves are secured by means of round 25mm steel hoops with an allowable stress of 105 MPa. Find the maximum spacing of the hoops to safely secure the pipe. Assume that there is an initial tension of 7,000 n applied to the hoops.

A continuous wood stave pipe is 3.0 m in diameter and is in service under a head of 30.0 m of water. The staves are secured by means of round 25mm steel hoops with an allowable stress of 105 MPa. Find the maximum spacing of the hoops to safely secure the pipe. Assume that there is an initial tension of 7,000 n applied to the hoops.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the minimum thickness of plate which may be used if the stress is limited to 15 ksi and the internal pressure is 125 psi. The tank is fabricated from steel plate.
The pressure tank shown is fabricated from spirally-wrapped metal plates that are welded at the seams in the orientation shown. The tank has an inside diameter of 60 in. and a wall thickness of 0.375 in. For a gage pressure of 131 psi, determine the normal stress perpendicular to the weld.
Q3: . A crank built up from cylindrical sections by welding required a loading of 250 lb to overcome the resistance when in the post- tion shown. (a) Compute the maximum normal and shear stresses induced in the section A-A. (b) Determine the maximum shear stresses induced in parts I, II, and III. Ans. (a) (max) = 29,000 psi, T(max) = 15,000 psi (b) 10,550 psi for part I, 6880 psi for II, 15,000 psi for III --A III II 1 Dia. Dia. Fig. 2-38 250 lb 150 "Dia.
Answer the following for the section at Point D Only Calculate the distributed load "w" that: Will cause the section crack Will cause the reinforcement to yield. Material Properties: F'c = 5000 psi Fy = 60000 psi Es = 29000000 psi Ln = 27 ft L wl₂² 16 wl,² 14 CD L wl,2 vl₁² 10 11 win² 16 h: 28 in A=4 in² b=14 in n d: 25 in
A cylindrical pressure tank is fabricated by butt-welding 19 mm-thick plate with spiral seam shown below. The pressure in the tank is 2.76 MPa, and an axial load of 133.5 KN is applied to the end of the tank through a rigid bearing plate. Determine the normal stress and shearing stress perpendicular to the weld. 133.5 KN 1.2 m I.D. Rigid plate how to
Hand written and clean solution please
A bolted connection between a vertical column and adiagonal brace is shown in the figure below. Theconnection consists of three 5/8-in. bolts that join two 1/4-in.end plates welded to the brace and a 5/8-in. gusset platewelded to the column. The compressive load P carried bythe brace equals 8.0k.Determine the following quantities: (a) The averageshear stress τavein the bolts, and (b) the average bearingstress σbbetween the gusset plate and the bolts. (Disregardfriction between the plates.)
Q1 : For a yield strength of 50 kpsi find the factor of safety at point A using the maximum shear stress theory. [Ans 2.34] 1.25 in.- 60 in.- 200 Ib 200 Ib -24 in.- 24 in.- 1.5 in. Web and flange thickness 0.125 in
Class work: The two solid cylindrical steel rods AB and BC are welded together at B and loaded as shown in the figure. Knowing that the normal stress must not exceed 175MPa in rod AB and 150MPa in rod BC determine the smallest allowable values of d, and d₂. استنساخ 200 m مكتب المدير مقابل كلية الهندسة مجمع فاطمة 250 mm B 40 kN - d 30 kN
STEEL STRUCTURES
2 - please provide a clear and complete solution, thanks!
DETERMINE THE CONCRETE AND STEEL STRESS AT THE FIXED SUPPORT C.