A constructed beam ACB has a cross section of 1.5in X 1.5 in supported by a column CE having a cross section of 1in X 1in. Assuming that the allowable stresses for the connecting bolt for point C is 24 ksi for shearing and 30 ksi for bearing, determine the minimum diameter of the bolt required in Inches.

Q: Compute its design strength based on rupture in kiloNewtons..* 412 485 453 389 438 This is a…

A: Given, Fu = 400 MPa  Fy = 248 MPa D = 16 mm  Dh = D + 2

Q: Determine the maximum load P that can be applied to the lap joint connected by three – 16 mm…

A: STEEL STRUCTURES:

Q: A 1 ⁄2 × 5-inch plate of A588 steel is used as a tension member. It is connected to a gusset plate…

A: Given: 1⁄2 × 5-inch plate of A588 steel. ⇒Width, b=12in⇒Thickness, t=5 in Diameter of bolts = 5⁄8…

Q: Prob 01: An 18” depth beam is bolted to a 24” depth girder is connected similar to that in figure…

A: Given:- The depth of the beam = 18 inch = 457.2 mm The depth of the girder = 24 inch = 609.6 mm The…

Q: As shown in Figure 7, members AC and BD are used to brace the pin-connected structure against a…

A: Factored load, 12 kips. A36-steel properties: fu = 58 ksi fy = 36 ksi

Q: O Which of the following gives the max. shearing stress if P = 40 kN, e = 45", a = 300 mm, b- 450…

A:

Q: Determine the maximum axial compressive service load that can be supported if the live load is twice…

A: Given:- HSS 8×4×14ASTM A500 Grade BTo find:-maximum axial compressive service load using,a)…

Q: EXERCISES Eleven sets of illustrations and the corresponding free-body diagrams of building-related…

A:

Q: Problem 2. Using 22 mm diameter bolt, compute: a. t for Palone b. t for moment alone c. Critical…

A: Tension member connection and splice: It subjects the bolts to powers that will in general shear the…

Q: determine the capacity of the details shown below. A992: Fy=50ksi, Fu=65ksi A36: Fy=36ksi, Fu=58ksi…

A:

Q: 60 25. 26. O A. 424 B. 508 Situation 8. The given angle bar L125x75x10 is connected to a 12 mm…

A: Given, L125 x 75 x 10 t = 12 mm  db = 20 mm  Fy = 248 MPa Fu = 400 MPa   NOTE : As per guidelines,…

Q: A 3/4 in (thickness) X 5 in (height) steel plate is connected to another one through two bolts of…

A:

Q: 10/.. find the shear stress in bolts (4 80 kN 80 kN 8-bolt DIA. 10 MM 80 kN 80 kN 8-bolt DIA. 10 MM…

A: Given, P = 80kN  Diameter of bolt = 10mm No. Of bolts = 8, Shear stress on the bolt=…

Q: The tension member is fastened togother using two bolts, one on each side of the member as shown.…

A:

Q: As shown in the figure below, a C7 x 12.25 tension member of A572 Gr 50 steel is connected to the…

A: Answer  We know that allowable strength of a member is given by minimum of the following strength 1)…

Q: 4. The steel truss that is shown in the Figure below is loaded with three concentrated service live…

A: Factored live load = 200 kNForce on the member is calculated using the Influence line diagram.Member…

Q: The tension member shown is an L150 × 87.5 × 8. The bolts are 19 mm in diameter. If A36 steel is…

A:

Q: A W300 x 67 has two lines of 20 mm dia. Bolts in each flange (3 bolts in each line which has spacing…

A: Bolted connections are used to attach the two metal pieces with the bolts. First, place the holes…

Q: 4. The steel truss that is shown in the Figure below is loaded with three concentrated service live…

A: Factored live load = 200 kNForce on the member is calculated using the Influence line diagram.Member…

Q: Determine the maximum factored LRFD tensile force capacity in tension only (no block shear). The…

A: We know that Maximum factored LRFD tensile force capacity of the member is given by minimum of the…

Q: what is the bolt shear capacity of the shear connection in kips?

A: A 325 boltsBolt diameter d = 3/4 inNumber of bolt in shear connection n = 16       (top and bottom…

Q: SITUATION II: Calculate the permissible tensile load P 50 under the following conditions: Fy3248…

A:

Q: Calculate the tightening torque for an SAE 5, ASTM449, 13UNC grade bolt with a diameter of 1/2 inch.…

A: The application of preload to a fastener by the turning of the fastener's nut. Friction points…

Q: An angle L5x5x% tension member of A36 steel is connected to a gusset plate with six 3/4-inch…

A: Tension member L5x5x5/8A36 steel.Bolt diameter, db = 3/4 in6 bolts spaced 3 inThe length of the…

Q: Calculate the strass In each mamber and identify what the factor of safely to failure 13? 19

A: Given:- Cross section of the members is 3" x 10" To find:- Stress in each members Concept:- Method…

Q: The tension member shown below is a C 310 x 30.8 of A572M gr 345 steel materials. Will it safely…

A:

Q: a. Determine the ultimate tensile strength of the tension member (channel) based on its gross area.…

A: For channel fu = 450MPa fy = 345MPa

Q: Plate connection with bolts with shear strength value T=200 MPA is given in the figure. Determine…

A: It is required to determine the area of the bolt. T=PA Here T is the shear strength, P is the…

Q: Use ASD to determine the width of the 5/8 inch thick A36 plate subjected to tension as shown below.…

A: ASD5/8 inch thick A36 platedead load, PD=85 kiplive load ,PL=80 kipTwo rows of 5/8 inch standard…

Q: Governing Ultimate Tensile Capacity based on Yielding of gross section

A: Gross area Ag=11.2 in2Yield stress Fy=50 ksiUltiate stress Fu=65 ksiy¯=3 inLength of weld L=12…

Q: Home work Q1/ steel bar of rectangular secton 5cm by the 16 cm carries an axial load of 50 kn.…

A: As per guidelines please post Q 2 separately

Q: Determine the capacity of the details shown below. A992: Fy=50ksi, Fu=65ksi A36: Fy=36ksi,…

A: Tensile Strength: The Tensile strength of a material defines as the stress in tension that the…

Q: limited to 48 ksi, determine the minimum bolt diameter that may be used for this connection. (coc00…

A: To find the minimum diameter of bolt (dmin.)-

Q: Determine the nominal axial compressive strength of the members shown in the following

A: The values and figure given in the question are as follows Length of column=L Effective length of…

Q: 1.2) The effective net area is A) 5.510 in B) 4.536 in C) 4.536 in D) 4.109 in

A: A double-channel shape, 2 C8*18.75, is used as a tension member. The channels are bolted to a…

Q: The tension member shown in the figure is connected to a gusset plate as shown with 1.2-inch…

A:

Q: A single angle tension member L89x89x9.5 with an area of 1,800mm2 connected to a

A: L89x89x9.5 Ag= 1800mm2 d= 22mm do= 25mm

Q: Problem 1: Hanger in Tension with Block Shear The W12 X 53 tension member shown below has two rows…

A: Given: db = 1 in Fy = 50 ksi Fu = 65 ksi section properties: W 12 x 53 Ag=15.6 in2 d = 12.1 in tw =…

Q: The five-bolt connection shown must support an applied load of P = 371 kN. If the average shear…

A: Given Load 371 kNStress 174 MPaNumber of bolts 5To find out Minimum diameter

Q: For the welded angle, determine the maximum tensile strength. Assume A992 grade steel. 6" 4" -Pu -L5…

A:

Q: Please help me answer the first question

A:

Mechanics of Solids

It is the study of the behavior of solid materials, their characteristics under various circumstances such as variation in external forces, temperature, and other internal factors. It is one of most important study in the field of engineering science, especially chemistry and mechanical engineering. In rigid body, the idealization of the solid body in which deformation is neglected. Deformation is known as the force acting on the solid state system which exerts change in its shape of the body but it continues to be at rest or in a uniform motion but it cannot accelerate. But those solid systems do have elasticity, compressibility and can be bent. This field is very vast since there are wide range of materials around us.