A cone of base diameter 100 mm and height 150 mm is resting upon HP on its base. A horizontal square through hole of 40 mm side is cut in the cone such a way that the axis of the hole intersects the axis of the cone at a height of 16 mm from the base. If the four sides of the hole are equally inclined to HP, draw the development of the lateral surface of the cone.

Q: 5 kN 70° 7 kN Determine the magnitude of F1 for equilibrium. Set F2 = 6.0kN . Determine the angle…

A: Given F2= 6kn Need to find F1

Q: he resultant of the force system shown is a force-couple R and ?? acting at point O. Determine the…

A: Question is based on a force system . Loading condition on system and dimension of member are given…

Q: Consider the gravity dam (Figure 2) whose concrete density is noted Pb. The vertical dam profile has…

A: Dam height, hb = 30 m Dam width, lb = 44 m Dam length, Lb = 25 m α = 650 β = 450 Find:

Q: 3

A:

Q: 2) If the beam is subjected to a shear of V = 15 kN, determine the web's shear stress at A and B.…

A: Given : V = 15 kN Location of Neutral axis = 0.1747 m from the bottom INA = 0.2182 X 10-3 m4 This…

Q: Q.3) Two structural members AB and BC (shown below) are connected by a 0.75- inch diameter pin at B…

A: Pin diameter= 0.75 in Maximum average normal stress in members AB and BC

Q: Z. 50 kN 200 kN 2 m 3 m 150 kN Fig. P3.58

A:

Q: draw the shear flow diagram due to the vertical shear force V and calculate the distance e locating…

A:

Q: 1. If the values of T1= 150, T2= 175 and T3=269, compute for the value of the resultant. and the…

A:

Q: 8.0" 1.5 y C 6.0" 3.0" 2.0* 3.0"

A:

Q: If the values of T1= 150, T2= 175 and T3=269, compute for the value of the resultant. and the angle.…

A:

Q: slope at A

A:

Q: Forces P and Qx are applied at point C of the rectangular plate. A 45-degree strain rosette…

A: The given figure is shown below:

Q: (3) Compute the moment of inertia with respect to the centroidal axis. Properties of 8x6x1 angle =…

A: Note- Since we answer one question at a time so we will answer the first one. Please resubmit…

Q: Q/ The following sketch include inverting readings of some stations. Construct a table of complete…

A: Height of Instrument=HIBenchMark=BMBack sight=BSFore Sight=FSReduced Level=RLAssume the three change…

Q: Determine the volume of the solid generated by rotating the semiparabolic area shown about (a) the y…

A:

Q: Determine Kinematic determinacy

A:

Q: 4.12 The homogeneous cylinder of weight W rests in a frictionless right-angled corner. Determine the…

A: Given data:  4.12  .   the homogeneous cylinder of weight "w"rests in a frictionless right-angles…

Q: 3.Show the magnitude and direction of the internal forces on the section k=1 meter to the right of…

A:

Q: Locate the centroid of the homogeneous solid formed by revolving the shaded area about the z axis.

A:

Q: Determine Ely at the midspan of the beam. 50 kN Wo= 10 kN/m 2 m D 2 m 4 m A

A: To find the deflection at any point first calculate reactions on supports. The divide beams into…

Q: Situation 3: The magnitudes of the three forces acting on the plate are T₁ = 100 kN, T2= 80 kN, and…

A: Given data

Q: For the given truss shown, determine the reaction in kN of the hinge support D

A: Question is based on the truss supported  roller and hinge support . Magnitude of loading and length…

Q: 1.1.9 - Show all work please.

A: To solve the given problem, we need to determine the components of a 6.2 kN force along two oblique…

Q: A 120 N weight is attached to the cable that is wrapped around the 50-N homogeneous drum. The shaft…

A: Determine the diameter of drum, and the reactions at A and B.

Q: 5.38 A vertical, circular cross-sectional jet of air strikes a coni- cal deflector as indicated in…

A: Given: D = 0.1 m V1 = 30 m/s The density of air = 1.23 kg/m3 FA = 0.1 N To find: The mass of the…

Q: degree of indeterminacy.

A: Degree of Indeterminacy is of two types 1. Static indeterminacy  2. Kinematic Indeterminacy

Q: A 75 mm 75 mm -100 mm E Fig. P3.30 200 N 200 N B 750 N D 3.30 The shearing forces exerted on the…

A: Given data:

Q: Determine the axial forces, shears, and bending moments at points A and B of the structure shown. 1.…

A: Consider the figure,

Q: The shaft below is fixed at D. A hole with a diameter of 44-mm has been drilled into portion CD of…

A: Given that : Diameter of hole = 44 mm G  = 77 GPa A) Angle of twist of end A with respect to end D…

Q: 1. If the angular velocity of link AB is wAB = 3 rad/s, determine the velocity of the block at Cand…

A:

Q: 4m

A:

Q: angular position of the slotted bar is e = 10t^2 rad. Determine the (measured magnitude and…

A: Sine law: - It is defined as an equation by which one can relate the length of side of triangle to…

Q: लेत P 3P 4 Į + J M 8m JAN J k 9m IL •G -4 3.5m 3.5m 4m

A:

Q: For the given structures, determine the degree of indeterminacy. 7. A

A:

Q: The two structural members, one of which is in tension and the other in compression, exert the…

A:

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?