A conducting rod is free to slide on two parallel conducting bars. A resistor is connectedto the end of the bar. The conducting bar and the rod have negligible resistance. Aconstant magnetic field is directed perpendicularly into the page. The power dissipatedin the resistor is 64 W. The constant speed of the rod is v=8.00 m/s. Find the magnitudeof the applied force that is needed to move the rod with this constant velocity. Give youranswer in N.İletken bir çubuk iletken raylar üzerinde serbestçe kayabilmektedir. Rayların ucuna Rdirenci bağlanmıştır ve çubuk ile rayların dirençleri ihmal edilebilecek kadar küçüktür.Sayfa düzleminden bize doğru düzgün manyetik alan uygulanmaktadır. Dış bir kuvvetile çubuk sola doğru sabit v=8,00 m/s hızıyla çekilirken dirençte harcanan güç 64 Wolmaktadır. Hızın sabit olması için gerekli dış kuvvetin büyüklüğü N cinsinden nedir?RYanıtınız

Write the given values in the question. P=64 Wv=8 m/s

A conducting rod is free to slide on two parallel conducting bars. A resistor is connected to the end of the bar. The conducting bar and the rod have negligible resistance. A constant magnetic field is directed perpendicularly into the page. The power dissipated in the resistor is 64 W. The constant speed of the rod is v=8.00 m/s. Find the magnitude of the applied force that is needed to move the rod with this constant velocity. Give your answer in N. letken bir çubuk iletken raylar üzerinde serbestçe kayabilmektedir. Rayların ucuna R direnci bağlanmıştır ve çubuk ile rayların dirençleri ihmal edilebilecek kadar küçüktür. Sayfa düzleminden bize doğru düzgün manyetik alan uygulanmaktadır. Dış bir kuvvet ile çubuk sola doğru sabit v=8,00 m/s hızıyla çekilirken dirençte harcanan güç 64 W olmaktadır. Hızın sabit olması için gerekli dış kuvvetin büyüklüğü N cinsinden nedir? B R

A conducting rod is free to slide on two parallel conducting bars. A resistor is connected to the end of the bar. The conducting bar and the rod have negligible resistance. A constant magnetic field is directed perpendicularly into the page. The power dissipated in the resistor is 64 W. The constant speed of the rod is v=8.00 m/s. Find the magnitude of the applied force that is needed to move the rod with this constant velocity. Give your answer in N. letken bir çubuk iletken raylar üzerinde serbestçe kayabilmektedir. Rayların ucuna R direnci bağlanmıştır ve çubuk ile rayların dirençleri ihmal edilebilecek kadar küçüktür. Sayfa düzleminden bize doğru düzgün manyetik alan uygulanmaktadır. Dış bir kuvvet ile çubuk sola doğru sabit v=8,00 m/s hızıyla çekilirken dirençte harcanan güç 64 W olmaktadır. Hızın sabit olması için gerekli dış kuvvetin büyüklüğü N cinsinden nedir? B R

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

show thatvthis is a magnetic flux density: then prove and interpret it with reasons on each step
The metal sphere in figure hangs by a thread. When the north pole of a magnet is brought near, the sphere is strongly attracted to the magnet. Then the magnet is reversed and its south pole is brought near the sphere. How does the sphere respond? Explain all possible cases. S Metal
A coil with 2000 loops on its length has a diameter of 2cm. A current of 5A is sent through it which is perpendicular to the field with a flux density of 0.05 T. Determine the torque on the loop.
Solve the following problem neatly and completely on your answer sheet.
A solenoid 500 cm long and 10 cm in diameter is wound with 1500 turns. Find the energy stored in the magnetic field when a current of 5 A flows
8-9 only
compute the reluctance of the magnetic circuit
An iron circuit with a small 0.75 mm air gap is shown in Figure 1. A 6000 turn coil carries a current I = 18 mA which sets up a flux within the iron and across the air gap. The cross section of the iron is a consistent 0.8 cm?, and the mean length of the flux path is 0.15 m. a) Redraw the magnetic circuit using schematic symbols of an electric circuit with reluctance in each part of the circuit. b) State's Ohm's Law for magnetic circuit. c) By neglecting the effect of fringing, calculate the reluctance of the circuit. d) Find the flux within the core. N = 6000 Iron circuit (4, = 800 for iron). Figure 1
Calculate the magnetic induction in air at a point 5 cm from a long straigh wire carrying a current of 15 A. As shown in the figure below, two long parallel wires are 10 cm apart in a and carry currents of 6.0 A and 4.0 A. C D 10 cm 6.0 A 4.0 A Show that the force per unit length on wire C can be expressed as 24.0 Ho 0.20 a
Please i need the final answer very urgent
d=0.8 B=1.6T R1=25 R2=10 R3=10 E=120V m=100g
Pls quick. I need the final answer