A concrete cube 60 cm on each edge (sp. gr. 2.40) rests on the bottom of a tank in which sea water stands to a depth of 5 m. The bottom edges of the block and sealed off so that no water is admitted under the block. Find the vertical pull required to lift the block. Note: The answer should be 13.76 kN.

A concrete cube 60 cm on each edge (sp. gr. 2.40) rests on the bottom of a tank in which sea water stands to a depth of 5 m. The bottom edges of the block and sealed off so that no water is admitted under the block. Find the vertical pull required to lift the block. Note: The answer should be 13.76 kN.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Please please correct answer And solve both part
Situation 1| An overhang beam is loaded as shown below. The beam cross-section was built by attaching two (2) channels to a 9mm thick plate using 16mm rivets. The property of the channel is given below: Depth, D = 225 mm Flange Thickness, t, = 9mm Flange Width, B; =112.5 mm Web Thickness, tw=9 mm The allowable flexural stress on the beam is 180 MPa. Rivets has a capacity of t= 100 MPa on shear, for bearing, o,=200 MPa on single shear, o,-260MPA on double shear. 1. Determine the location of centroid, y, from top of the beam in mm. 2. Determine the moment of inertia, I, of the section in mm“. 3. Determine the maximum allowable moment, Mall, in kn-m, base on the beam's cross-section.
Current Attempt in Progress The horizontal shaft with a diameter of d- 43 mm is supported by a thrust collar that rests on a 29-mm-thick plate. The thrust collar is 20-mm thick. The thrust collar has an outer diameter of Dcollar - 63 mm. Determine the load P that causes an average shear stress of 69 MPa on the cylindrical surface of contact between the shaft and the thrust collar. Thrust collar area Plate d Thrust collar Dcollar Answer: P- kN
Please show complete solution. Solve the internal forces using cantilever method.
Solve letter B only; Subject:Hy
Solve b
A tank containing water moving horizontally with a constant linear acceleration (3.5m/sec2), and vertical acceleration decreases by (25%) from the horizontal acceleration. The tank was (3m) high, (2.5m) length and (1m) width. Determine the force on the bottom of tank if the water level at rest was (2m)
Someone can help me with this one please
1. Design the spacing of the main bars and temperature bars of a one-way slab having a total span of 5 m. The slab is supported with hinge in the left support and a vertical cable located 1.5 m from the right support. The distance between the cables of the slab is 2.3 m. The slab is to carry a live load pressure of 2.4 kPa and a dead load pressure (including self-weight) of 4 kPa. Assume f'c = 27.6 MPa and fy = 276 MPa for main and temperature bars. Use 12 mm Ø for main bars and 10 mm Ø for temperature bars. The slab is not exposed to earth or weather. Use thickness of slab of 120 mm. Use NSCP 2001.
An open tank in the shape of frustrum of a cone is bound by two hoops one at the top and another at the bottom. The diameters at the top and bottom are 2m and 3m respectively. If total busrsting force is to be taken care if by the hoops, find the tension in each hoop if water stands 2m in the tank. Height of tank is 3m.
The rectangular (0.6mx0.9m) sluice AB blocks liquid with a specific gravity of 0.79. The sluice door weighs 300N and finds the force that must act on the cable BCD to open the sluice door.