An open tank in the shape of frustrum of a cone is bound by two hoops one at the top and another at the bottom. The diameters at the top and bottom are 2m and 3m respectively. If total busrsting force is to be taken care if by the hoops, find the tension in each hoop if water stands 2m in the tank. Height of tank is 3m

Q: To close a gate valve it is necessary to exert two forces of 60 lb at opposite sides of a handwheel…

A: Given data,  Handwheel diameter = 3 ft Force = 60 lb Bar length = 4 ft To draw FBD and force…

Q: Determine all the forces acting on the structure shown. Also, indicate the type of force  acting on…

A: To Determine all the forces acting on the given structure and state the nature of their forces.

Q: Determine the reactions at the supports.

A:

Q: The compound shaft consists of three segments made from steel, aluminum, and bronze. The shaft is…

A: Given data: A compound shaft consisting of three segments made from steel, aluminum, and bronze.…

Q: 2. The pipe assembly is subjected to the force of F = (600i + 800j - 300k) N. Determine the moment…

A:

Q: *1-44. The 150-kg bucket is suspended from end E of the frame. If the diameters of the pins at A and…

A:

Q: *1-44. The 150-kg bucket is suspended from end E of the frame. If the diameters of the pins at A and…

A: Given : Weight of bucket = 150 kg Dia of pin A = 6mm Dia of pin D = 10 mm To Find : Average shear…

Q: *1-44. The 150-kg bucket is suspended from end E of the frame. If the diameters of the pins at A and…

A:

Q: Qg: If the weightless half- cylindrical gate,show in figure below, is in equilibrium , what is the…

A:

Q: A circular tied column 490mm in diameter is reinforced with 10-20mm-diameter vertical bars.…

A:

Q: The T-beam for a floor system shown is cast monolithically with the slab. The beam has a simple span…

A: step 1-

Q: reactions at A & B.

A:

Q: Determine the member force on member EI.

A:

Q: 1 m diameter 4 m Water h 1'm

A:

Q: 15 KN 10 KN 10 KN 1.0m 1.0 m H RAX 2.0m 20m 2.0 m 2.0 m 5 KN REY RAy

A: Solve for the forces of members CG, GH, AH, BC, BG, BH, and AB

Q: Question No. 2 [30%]: Determine the forces in cables AC and AB 1.5 m needed to hold the 20-kg ball D…

A:

Q: 5. The spool has weight 300 N and radius of gyration Ko = 0.36 m. If the block B has eight Wb = 267…

A:

Q: 2. A 10m high cantilever wall separates water and oil as shown. The water and the oil are 8m and…

A: To find support reaction

Q: Determine the positive moment in the direction of the short side for deck 6. Take the design load to…

A:

Q: The steel framework is used to support the reinforced stone concrete slab that is used for light…

A:

Q: For the loaded structure below, replace the force system with a single resultant force. Determine…

A: The  conversion of UDL into point load; P=(1/2)*3*42 P=6 KN from A at (2/3)*3=2 m

Q: What is the Maximum moment in kN-m. Given: w =48, a = 4, b = 4, and c = 2.

A:

Q: The wooden column is set at the base and at the top. Determine the load maximum eccentric P that can…

A: The given figure is shown below:

Q: onsider the ¼-circular curved gate hinged below. The gate radius is 3 m, its width (into the page)…

A:

Q: A sliding gate of height 1.4m and width 2.8 lies in vertical plane that weighs 25kN. Determine the…

A: Pressure at a point: The pressure at a point in fluids is defined by pascal's law. Pascal's law…

Q: 2. A load P is supported by two concentric steel springs. The inner spring consists of 30 turns of…

A: Asked: To determine the maximum value of load P carried by two concentric springs.   Given: For…

Q: A hollow shaft of external and internal diameters as 100 mm and 40 mm respectively is transmitting…

A: Given - External diameter, D  = 100 mm Internal diameter, d = 40 mm Transmission of power, N = 120…

Q: Consider the ¼-circular planar gate hinged below. Its radius is 3 ft and its weight is negligible.…

A: Given: The radius of the circular plane is 3 ft. The specific weight of water is 62.4 lb/ft3.

Q: 6 m B 60 KN ļº 60 kN P 60 KN 4 panels at 8 m = 32 m EA = constant Sw E Determine the force in member…

A: Given values: Consider the truss given. Using method of joints and method of sections the unknown…

Q: A. Solve for the force Acting on the C ( Horizontal) Ch B. SOlve for the force acting on the C…

A: The given figure is shown below:

Q: Determine the forces of DF, EF, FG (Tension or Compression)

A: Consider the given truss. Let the vertical reactions at A and C are RA and RC respectively. Take the…

Q: A 115mm thick concrete slab is supported by beams 300mm wide with effective depth of 650 mm. The…

A:

Q: A 250-lb bucket is suspended from a cable on the wooden frame. Determine the resultant internal…

A:

Q: Part A Determine the resultant couple moment acting on the pipe assembly. Assume (Mc)1= 530 lb?ft,…

A: Given :

Q: A solid shaft has to transmit 120 kW of power at 160 rpm. If the shear stress is not to exceed 60…

A:

Q: The pipe assembly is subjected to the force of F = {600i + 800j - 500k} N. Determine the moment of…

A: Considering the given figure as follows:

Q: C 136 kN [63 kN 3.6m -4.8 4.8 +4.8m

A: Finding out the given member forces.

Q: 2. The pipe assembly is subjected to the force of F = (600i + 800j – 300k) N. Determine the %3D…

A:

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?