A concrete cube 60 cm on each edge (sp. gr. 2.40) rests on the bottom of a tank in which sea water stands to a depth of 5 m. The bottom edges of the block and sealed off so that no water is admitted under the block. Find the vertical pull required to lift the block

A concrete cube 60 cm on each edge (sp. gr. 2.40) rests on the bottom of a tank in which sea water stands to a depth of 5 m. The bottom edges of the block and sealed off so that no water is admitted under the block. Find the vertical pull required to lift the block

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A rectangular vertical gate that has a width of 0.6 meters, height of 2.45 meters, and it weighs 1.78kN is hinged at the bottom. On the right side of the gate the water has a height of 1.8 meters while on the left side of the gate the water has a height of 4.9 meters. However, the gate is held in place by horizontal force F applied at the top of the gate. Determine the horizontal force F and the reactions at the hinge. The weight of water is 9.81 kN/m3
The 600-Ib, 20ft-wide rectangular gate shown is hinged at B and leans against the floor at A making an angle of 45° with the horizontal. The gate is to be opened from its lower edge by applying a normal force P at its center. A. Determine the magnitude if the hydrostatic force acting on the gate using the hydrostatic panel equations. Express your answer in kips.
3/56 An 80-lb sheet of plywood rests on two small wooden blocks as shown. It is allowed to lean 20° from the vertical under the action of a force P which is perpendicular to the sheet. Friction at all surfaces of blocks A and B is sufficient to prevent slipping. Determine the magnitude P and the vertical reaction forces at A and B. Z P -20° D 4' 1' E A -5' DE = 3 ft PROBLEM 3/56 2' B - y
5. A 30 cm radius Cast iron main leads from a reservoir whose water surface is at EL. 1590m. In the heart of the city the main, below ground level, is at EL. 1410m. (a) What is the net pressure (b) Assuming static conditions, what is the stress in the pipe wall if the wall thickness is 12.00 mm and the external soil pressure is 250 kPa?6. A continuous wood stave pipe is 2.5 m in diameter and is in service under a head of 30.0 m of water. The staves are secure by means of round 25 mm steel hoops with an allowable stress of 105 MPa. Fine the maximum snarings of the hoops to safely secure the nine.
1.50 The cylindrical steel column has an outer diameter of 4 in. and inner diame- ter of 3.5 in. The column is separated from the concrete foundation by a square bearing plate. The working compressive stress is 26 000 psi for the column, and the working bearing stress is 1200 psi for concrete. Find the largest force P that can be applied to the column. Į 3.5 in 0.125 in. 0.75 in. 2800 lb 7 in. FIG. P1.50 1.5 in. 6 in.- 14800 lb B FIG. P1.49 6 in.-
A circular nylon pipe supports a downward load P, = 10kN, which is uniformly distributed around a cap plate at the top of the lower pipe. A second load Pa = 20 kN is applied upward at the top. The inner and outer diameters of the upper and lower parts of the pipe are d, = 30 mm, d, = 60 mm, d, = 55 mm, and d, = 65 mm, respectively. The bottom pipe has length 400 mm and the upper pipe has length 300 mm. Calculate the axial normal stress in each pipe segment. Calculate the strain in each pipe segment if the clongation of the upper pipe is 3.29 mm and the elongation of the bottom part is 1.25 mm.
The beam below is subjected to a uniformly distributed load of 2 kN/m from a A to C, and a uniformly varying load (2kN/m to 5 kN/m) is applied at C to F. Two uniformly distributed loads support the beam on the location shown below. U, 9-2 w, 1 (m) 1 ( 2 (m) 1 (m) D 5. Determine the magnitude of W; in kN/m. 6. Determine the magnitude of W, in kN/m. 7, Determine the maximum moment. B. Determine the location of zero shear.
Name: Class: ......... Assignment No. 3 Q4- A rectangular gate 6 ft tall and 5 ft wide in the side of an open tank is held in place by the force F as indicated in Figure. The weight of the gate is negligible, and the hinge at O is frictionless. (a) Determine the water depth, h, if the resultant hydrostatic force of the water acts 2.5 ft above the bottom of the gate, i.e., it is collinear with the applied force F. (b) For the depth of part (a), determine the magnitude of the resultant hydrostatic force. (c) Determine the force that the hinge puts on the gate under the above conditions. Water Hinge O Gate 6 ft 2.5ft Name: Class: Assignment No. 3
A triangular gate having dimensions shown is hinged at its top at A. The gate rests on a frictionless surface at B. A.) Determine the hydrostatic force acting on the gate. B.) At what distancce from the centroiid of the panel is the hydrostatic force acting?