A compound bar consists of a circular rod of steel of diameter 25 mm, rigidly fitted into a copper tube of internal diameter 25 mm and thickness 2.5 mm. If the bar is subjected to an axial load of 100 kN, find the stresses developed in the two materials. Given, E, = 2 x 105 N/mm2 and E = 1.2 x 105 N/mm2. %3D

A compound bar consists of a circular rod of steel of diameter 25 mm, rigidly fitted into a copper tube of internal diameter 25 mm and thickness 2.5 mm. If the bar is subjected to an axial load of 100 kN, find the stresses developed in the two materials. Given, E, = 2 x 105 N/mm2 and E = 1.2 x 105 N/mm2. %3D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Show complete solution please.
8. A rigid bar AB is supported by three rods. A load P = 250 kN is applied to the bar. The modulus of elasticity of copper is 110 x 10°6 kN/m^2 and modulus of elasticity of steel is 200 x 10°6 kN/m^2. Steel rod A= 900 sq. mm Steel rod A= 900 2m sq. mm Copper A=1200 sq. mm 2m B 1m 1m Determine the deformation in the rods (in mm). * Your answer
2. The rigid bar of negligible weight is pinned at O and attached to two vertical rods. Assuming that the rods were initially stress-free. What is the largest load P that can be applied without exceeding stresses of 160 MPa in the steel rod and 65 MPa in the bronze rod? - 2.5 m 2 m 2 m Steel A=1000 sq. mm Bronze A=400 sq. mm E=200 GPa E=83 GPa L=1.6 m L=2.2 m P
2. A rod is composed of an aluminum section rigidly attached between steel and bronze sections as shown in the figure. Axial loads are applied at the positions indicated. The cross-sectional area of the rod is 300sq.mm. Express your answer in MPa. Determine the stress in the steel. b. a. Determine the stress in the aluminum. Determine the stress in the bronze. C. STEEL ALUMINUM BRONZE 56kN 14kN -0.6m- -0.9m- -0.76m-
SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and attached to two vertical rods. Assume that the rods were initially stress-free. Allowable stress in steel is 120 MPa and in bronze is 60 MPa. For this problem, a = 1.8m; b = 1.3m; c= 1.7m. b C P Steel: A = 900 mm² Bronze: A=1200 mm² E = 83 GPa L=2.0m E= 200 GPa L = 1.5m What is the value of P without exceeding the allowable stress of steel, in kN? 250 340 280 O230
GIVEN: Bar has a cross-sectional area of 4 in? and is placed between two rigid immoveable supports when it is 30.00 inches long at a temperature of -20°F. REQ’D: A) The stress in the bar at 90°F if it were made of steel. Esteel = 10 x 10° psi asteel = 13 x 106/°F B) The final length of the aluminum bar
A bar made from aluminum (E = 72 GPa) has a diameter of 12 mm. When the bar is subjected to a tensile axial force P, its diameter is decreased by 0.018 mm. Assume the Poisson's ratio to be 0.33. Determine the value of loads P and its axial deformation. P d = 12 mm L 1.20 m P
Q1. An aluminum rod is rigidly attached between a steel rod bronze rod as shown in figure. Axial loads are applied at the positions indicated. Find the maximum value of P that will n exceed a stress in steel of 90 MPa, in aluminum of 140 MPa bronze of 120 MPa. Aluminum Вronze A= 300 Steel A=100 A=200 ЗР 2P 5P 2.5m 2.0 m 1.5 m
200KN A steel rod is rigidly attached between an aluminum and bronze rod. The diameters of each material are shown in the figure. A fixed support is rigidly attached to the right end of the bronze rod. Determine the stress each section in kPa. Aluminum Steel D=28mm D=20mm 20KN Bronze D=25mm 150KN
MN=85
A steel rod is rigidly attached between an aluminum and bronze rod. The diameters of eachmaterial are shown in the figure. A fixed support is rigidly attached to the right end of thebronze rod. Determine the stress each section in KPa.
2. A steel shaft (G = 80 GPa) of total length L = 3.0 m is encased for one-third of its length by a brass sleeve (G, = 40 GPa) that is securely bonded to the %3D %3D steel. The outer diameters of the shaft and sleeve are di = 75 mm and d2 = 90 mm, respectively. The maximum shear stress in brass is 70 MPa, maximum shear stress in steel is 110 MPa and the maximum allowable angle of twist is 5°. What is the maximum allowable torque that can be applied at the ends of the shaft? Brass Steel shaft di = 75 mm d2 = 90 mm sleeve T T A B 1.0 m- L = 2.0 m- 2 = 2.0 m d1 dy Brass- sleeve Steel shaft d2 d2