A composite beam is made of wood and reinforced with a steel strap located on its bottom side. It has the cross-sectional area shown. find the maximum stresses both in the steel and wood and draw the stress distribution for the cross section. Take Ew = 20 GPa and Est = 200 GPa.

A composite beam is made of wood and reinforced with a steel strap located on its bottom side. It has the cross-sectional area shown. find the maximum stresses both in the steel and wood and draw the stress distribution for the cross section. Take Ew = 20 GPa and Est = 200 GPa.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Compression steel Given: The beam cross-section shown have the following cross-sectional properties: f'c = 4000 psi Find phi Mn.
A small aluminum alloy [E = 65 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 125 mm. The cross-sectional dimensions of the tee shape are b = 15 mm, d = 23 mm, and t = 9 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 460 µɛ is measured from a strain gage located at c = 9 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? P 3P Strain gage D E H b. Answer: P = i 29254 N
Problem 6: The wood beam is subjected to a load of 12 kN. Determine the transverse shear stress at point A is located 75 mm from the lower surface of the beam. Also what is the bending normal stress at A? 12 KN + 300 mm TH 200 mm -2 m---1 4.1 75 mol IM
The composite bar is subjected to a normal force P = 7500 lb as shown in the figure. The section of the composite bar is composed of two hollow tubes and a solid steel core. Determine the axial stress developed in each bar. Use Ecu = 18 x 106 psi, Est = 30 x 106 psi, and Ebr = 16 x 106 psi.
/ For the rectangular reinforced concrete beam (shown below),determine the stress at the upper and lower fibers of concrete and at steel reinforcement if fc'=20 MPa
A composite beam is made of two brass [E = 97 GPa] plates bonded to an aluminum [E = 72 GPa] bar, as shown. The beam is subjected to a bending moment of 2420 N-m acting about the z axis. Assume b=64 mm, d1=36 mm, d2=13 mm. Determine: (a) the maximum bending stresses opy,Gal in the brass plates and the aluminum bar. (b) the stress in the brass obrj at the joints where the two materials are bonded together. Brass (2) d2 Aluminum (1) Brass (2) dz b Answers: (a) obr = i MPa, oal = i MPа. (b) Obrj MPa.
A square beam (w=0.03 m) is loaded with a point load of 1000 N and a moment load of 1000 Nm, as shown. i. Determine maximum deflection of the beam using step by step analytical equations. ii. Determine the Maximum stress in the beam using step by step analytical equations iii. For both top fibers and bottom fibers of the square beam, specify the type of the stresses.
A small aluminum alloy [E= 77 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 160 mm. The cross- sectional dimensions of the tee shape are b= 22 mm, d = 33 mm, and t= 4 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 410 uɛ is measured from a strain gage located at c = 10 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? %3D %3D %3D 3P Strain gage E Answer:
A composite beam is made of two brass [E = 120 GPa] bars bonded to two aluminum [E = 70 GPa] bars, as shown. The beam is subjected to a bending moment of 400 N-m acting about the z axis. Using a = 15 mm, b = 100 mm, c = 30 mm, and d = 65 mm, calculate (a) the maximum bending stress in the aluminum bars. (b) the maximum bending stress in the brass bars. Aluminum y Brass Aluminum b Brass C a d
A composite beam is made of two brass [E = 120 GPa] bars bonded to two aluminum [E = 73 GPa] bars, as shown. The beam is subjected to a bending moment of 445 N-m acting about the z axis. Using a = 15 mm, b = 125 mm, c = 30 mm, and d = 75 mm, calculate (a) the maximum bending stress in the aluminum bars. (b) the maximum bending stress in the brass bars. Z Aluminum C Aluminum Answers: (a) Ogl Brass (b) Obr= i i b Brass a MPa MPa
QU A composite beam is fabricated by bonding a steel bar and a brass bar and is subjected to the bending moment M = 200 N-m. Determine the maximum bending stress in the brass and steel. Given: E, =200 GPa, E, = 100 GPa Brass 20 }o | Jakrtal
A reinforced concrete beam is shown in the figure below. 0.75-in, diameter rods Wo 20 in. 2.5 in. 8 ft- 8 ft 10 in. Part A Determine the maximum uniform distributed load wn that can be supported by the reinforced concrete beam if the allowable tensile stress for the steel is (Ost )allow = 30 ksi and the allowable compressive stress for the concrete is (oconc )allow = 3 ksi . Assume the concrete cannot support a tensile stress. Take Est = 29(10) ksi , Econe = 3.6(103) ksi Express your answer to three significant figures.