A composite bar is fabricated by brazing aluminum alloy [E = 10,000 ksi] bars (1) to a center brass [E = 17,000 ksi] bar (2) as shown in the figure. Assume d = 1.00 in., a = 0.2330 in., L = 37 in. If the total axial force carried by the two aluminum bars must equal the axial force carried by the brass bar, calculate the thickness b required for brass bar (2). b = in. L Aluminum (1) (1) -Brass (2)

A composite bar is fabricated by brazing aluminum alloy [E = 10,000 ksi] bars (1) to a center brass [E = 17,000 ksi] bar (2) as shown in the figure. Assume d = 1.00 in., a = 0.2330 in., L = 37 in. If the total axial force carried by the two aluminum bars must equal the axial force carried by the brass bar, calculate the thickness b required for brass bar (2). b = in. L Aluminum (1) (1) -Brass (2)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A rectangular polypropylene [E = 6,200 MPa] bar (1) is connected to a rectangular nylon [ E = 1,400…

A: GIVEN DATA- Two bar connected at flange B For bar 1 A1=990mm2 , L1=1600mm , E1=6200MPa For bar 2…

Q: 2) A simply supported timber beam with a rectangular cross-section has been loaded perpendicular to…

A: Given beam:

Q: 1. The bar is made out of steel and is loaded as shown in figure Fig. - 1. Determine the design…

Q: If the design limit of a 1.5m x 2 m rectangular support beam with a safety factor 5 is 100 x 106…

A: Given: FOS=5Design limit, σd=100×106 N/m2A=1.5m×2mYoung's modulus = 20×109

Q: Below is the stress (o = Ee) vs strain (e = 4) behavior of oxygen-free copper (OFC) wires (W8) at…

Q: A hollow steel [E = 30,000 ksi] tube (1) with an outside diameter of 4.00 in. and a wall thickness…

Q: A rectangular polypropylene [E = 6,200 MPa] bar (1) is connected to a rectangular nylon [E = 1,400…

Q: A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E=…

Q: (b) A steel strut of height 2 m, and cross-section 50 mm x 24 mm, is subject to an axial compressive…

A: It is asked o find

Q: mm. The normal stress in the aluminum rod must be limited to 124 MPa, and the normal stress in the…

A: From the given data:

Q: 6. A cylındrical copper (E=110GPA) rod with length of 380mm, yield strength of 240MPA, is subjected…

A: Solution :- Given data :- E =110 GpaLoad P =66000 NLength of rod L =380 mm

Q: If the design limit of a 1.5m x 2 m rectangular support beam with a safety factor 5 is 100 x 106…

Q: A tie bar has to carry a load of 100kN. What must be the width of the bar, which is 12,7mm thick if…

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

A composite bar is fabricated by brazing aluminum alloy [E = 10,000 ksi] bars (1) to a center brass [E = 17,000 ksi] bar (2) as shown
in the figure. Assume d = 1.00 in., a = 0.2330 in., L = 37 in. If the total axial force carried by the two aluminum bars must equal the
axial force carried by the brass bar, calculate the thickness b required for brass bar (2).
b = i
in.
L
Aluminum (1)
(1)
عالمالو
Brass (2)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A rectangular polypropylene [E = 6,200 MPa] bar (1) is connected to a rectangular nylon [E = 1,400 MPa] bar (2) at flange B. The assembly (shown in the figure) is connected to rigid supports at A and C. Bar (1) has a cross-sectional area of A₁ = 1070 mm² and a length of L₁ = 1380 mm. Bar (2) has a cross-sectional area of A₂ = 2730 mm² and a length of L₂ = 510 mm. After two loads of P = 2.6 kN are applied to flange B, determine: (a) the forces in bars (1) and (2). (b) the deflection of flange B. A L₁ (1) P B L2 C
Rigid bar ABCD is supported by a smoth pin at D and by vertical aluminum alloy [E=10,000 ksi] bars attached at joints A and C. Bar (1) was fabricated to its intended length L1=40 in. Bar (2) was intended to have a length of 60 in.; however, its actual length after fabrication was found to be L2=59.88 in. To connect it to the pin at C on the rigid bar, bar (2) will need to be manually stretched by Δ=0.12 in. After bar (2) has been stretched and connected to the pin at C, a load P=20 kips is applied to the rigid bar at B. Use the following additional properties and dimensions: A1=A2=0.75 in2, a = 36 in, b =54 in, and c = 48 in. Determin: a) The normal stresses in bars (1) and (2). b) The deflection at A of the rigid bar.
A rectangular polypropylene [E = 6.200 MPa] bar (1) is connected to a rectangular nylon [E = 1,400 MPa] bar (2) at flange B. The assembly (shown in the figure) is connected to rigid supports at A and C. Bar (1) has a cross-sectional area of A₁ = 920 mm² and a length of L₁ = 1220 mm. Bar (2) has a cross-sectional area of A₂ = 2630 mm² and a length of L₂ = 570 mm. After two loads of P = 3.8 kN are applied to flange B, determine: (a) the forces in bars (1) and (2). (b) the deflection of flange B. (a) F₁ = F₂ = (b) UB = i i i A kN KN mm L₁ (1) P B L₂ (2)
A load P is supported by a structure consisting of rigid bar ABC, two identical solid aluminum alloy [E = 73 GPa] rods (1), and a solid bronze [E = 105 GPa] rod (2). The aluminum rods (1) each have a diameter of 10 mm and a length of L₁ = 2.7 m. They are symmetrically positioned relative to middle rod (2) and the applied load P. Bronze rod (2) has a diameter of 25 mm and a length of L₂ = 1.7 m. If all bars are unstressed before the load P is applied, determine the normal stresses in the aluminum and bronze rods after a load of P = 70 KN is applied to the rigid bar. L₁ B Answer: 01 = i 0₂ i L2 (2) (1) (1) MPa MPa
A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E = 14100 ksi] rods, and a solid steel [E = 28000 ksi] rod, as shown. The bronze rods (1) each have a diameter of 0.61 in. and they are symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has a diameter of 0.47 in. Assume L₁-39 in and L2-72 in. If all bars are unstressed before the load P is applied, determine the normal stresses in bronze rods (1) and steel rod (2) after a load of P = 29 kips is applied. O (1) A Answers: 0₁ = i 0₂ = i L2 (2) B P ksi. ksi. L