701951806016515050135120401059030756020451030151.E+051.E+06 1.E+07 1.E+08 1.E+09 1.E+10 1.E+11 1.E+12 1.E+131.E+051.E+06 1.E+07 1.E+08 1.E+09 1.E+10 1.E+11 1.E+12 1.E+13Frequency, rad/secFrequency, rad/secFigure 2Write the generalized form of the amplifier's transfer function,Vout (w).a.A(w):VinDetermine the value of the capacitor Cx.What should be the quiescent collector current of the transistor?b.C.|A{»}], dBLA(o), degrees A common emitter amplifier, with the circuit shown in Figure 1, is designed to have a Bode magnitudeand phase frequency response as shown in Figure 2. The BJT has the following parameters: B = 100,VA → 00, C = 500fF, and C = 10fF. Use Vr = 26mV, Rc = 10kN and note that the capacitor Cx isan external capacitor used to achieve the desired frequency response.VccVIN OVOUTCxRcFigure 1

A common emitter amplifier with the circuit shown in the figure : Given the values of the…

A common emitter amplifier, with the circuit shown in Figure 1, is designed to have a Bode magnitude and phase frequency response as shown in Figure 2. The BJT has the following parameters: B = 100, VA → co, C = 500fF, and Cu = 10fF. Use Vr = 26mV, Rc = 10KN and note that the capacitor Cx is an external capacitor used to achieve the desired frequency response.

A common emitter amplifier, with the circuit shown in Figure 1, is designed to have a Bode magnitude and phase frequency response as shown in Figure 2. The BJT has the following parameters: B = 100, VA → co, C = 500fF, and Cu = 10fF. Use Vr = 26mV, Rc = 10KN and note that the capacitor Cx is an external capacitor used to achieve the desired frequency response.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Please answer all subpart either dislike is ready please all subpart is compulsory please I will like only for all subpart
11. What is the configuration of the given amplifier circuit below?12. How are the coupling capacitors treated in the figure of #11 at AC?
Consider the integrating amplifier circuit in Figure 2. Using nodal analysis, derive an expression for vout for the integrating amplifier. In the circuit in Figure 2, exchange the positions of the 0.1uF capacitor and the 5k resistor. a. Use nodal analysis to generate an expression for vout. b. Using this expression, explain what function this circuit performs on an input signal.
4. An ac amplifier has a mid-band voltage gain of 250 and the cutoff frequencies are fi = 30Hz. Calculate the gain at the cutoff frequencies and the the value of f2 if the bandwidth is 29970 Hz.
Q.3 Figure Q.3 shows an AC equivalent circuit at high frequency for a common-emitter BJT amplifier circuit. The voltage gain, Ay is -40. 1502 4 pF + Em V, RL Vo 3pF 2kΩ 100pF IpF 4pF Figure Q.3: AC equivalent circuit at high frequency operation (а) Determine the high cut-off frequency due to the input side of the equivalent circuit, fHi- (b) Consider that the high cut-off frequency due to the output side of the equivalent circuit, fHo, is 80 MHz. State the dominant high cut-off frequency.
Figure 2 shows a typical BJT amplifier, with its parasitic capacitances displayed. The current gain of the transistor is B=150 and the voltage gain of the amplifier is Am =-125. The small signal resistances of the transistor are re =16 ohm and r0 = infinity, respectively. The values of resistors and capacitors in the figure are: R1 =80 kohm, R2 =20 Kohm, Rc = 2 Kohm, RE = 2 Kohm, Rs =50 W, RI=5 kohm, Cs=2 uF, Cc=2 uF, Ce =10 uF, Cbc =4 pF, Cbe = 10 pF, Cce =1 pF, Cwi = 4 pF, CWO = 9 pF, and Vcc = 20 V. a) Sketch a simplified circuit diagram of Figure 2 for high frequency analysis. b) Using the concept of "Miller effect capacitance", calculate the input and Output Miller effect capacitances of Figure 2, respectively. C) Determine the upper cut-off frequency of Figure 2 that is imposed by its input network only. d) Explain briefly the possible ways to increase the upper cut-off frequencv of this amplifier.
The capacitance of the resonant converter having fixed value of resonant frequency 65 Hz and inductance of 10 H is pF. In single phase fully controlled converter, if the ripple factor is 2 then the form factor of the converter is
Analog Electronic: Frequency Response of BJT and FET Amplifier
Q.3) In frequency domain enhancement, we have many types of low pass filter, mention them and explain the using of each one.
can i have help with parts d-f
This circuit represents a small signal amplifier.If C1= 1.5 μF, C2= 0.43 µF Assuming the transistor has: ac current gain =100. dynamic resistance = 100, and Internal Capacitances C= 42 pF, Chc-4pF, C=1pF. 1- Calculate the critical frequencies for the low frequency response. 2- Calculate the critical frequencies for the high frequency response. 3- Write the general formula for voltage gain as function of frequency. 4- Sketch the Bode Plot for the voltage gain magnitude. 2 T mill 1kQ2 O 560 ΚΩ 4.3 ΚΩ C2 HA R1 2 2,7 ΚΩ
Consider the circuit shown below: +Vcc RC SR, BDc RE Solve for VC in Volts given that: RC=0.31kOhms RE=1.08kOhms R1=2.55kOhms R2=4.27kOhms VCC=12.93 V Beta(dc)=131.16