A column with one end fixed and one end free has a critical buckling load of 100 N. For the same column, if the free end is replaced with a pinned end then the critical buckling load will be N (round off to the nearest integer).

Q: Find the centroid along y – axis of the shaded area. y - axis = mm. 14 70 -35--35–| Dimensions in mm

A:

Q: Find the location of the centroid from the bottom of the composite area consisting of a 10in square…

A:

Q: Determine degree of external indeterminacy

A: Given data : Number of external support reaction (R)=3+1+1=5

Q: 8. Find the particular solution of the following DE. a. D - 2D- 3)y 0; when x 0, y = 0, y -4. b. D2…

A:

Q: 1=200,000 wpa Fy= 250 mpa A = 3929 mm² ty = 12.7 mm Ix= 53.7 x 10mm¹ x = 117 mm Propertia of Channel…

A: Properties of channel section and W section are given

Q: A cube of edge 24mm is resting on the top of a frustum of cone of base diameter 60mm and top…

A: In the engineering graphics we can draw both the 2 dimensional projection and 3 dimensional…

Q: Determine maxium principal plane

A: We have to determine the maximum principal plane.

Q: Compute the sinA =0.4785 cosB= -0,52d -0.52d %3D tanc= 0 987

A: Converting the given values into the degree is a very simple and easy way. We can convert the given…

Q: Q.: Find the coordinate of the centriod of the shaded area 4 Y 3 m-

A: Given, Equation y=2x-30.5

Q: Define deflection angles.

A: A deflection angle is an angle between the onward extension of the previous leg and the line ahead.…

Q: 3m 2m Clay Sand 8 m Plan View || D₁. OB OB 4 m 4m 1 m 3m 2 4m AG=0 (1₁-1₂)2 I m = = 2²-1 늦쓸-5.5…

A: Given: Load, q = 400 kN/m2 Point A: Depth, ZA = 3-1 = 2 m

Q: Determine the y-coordinate of the centroid of the shaded area. y 0.25h 68° 68° --x Answer:ỹ = i

A:

Q: Problem 4. Determine the location of the centroid of the shape measured from the given axes. -3 in.-…

A:

Q: In certain building operation, it was necessary to remove a portion of B hall which was…

A: Calculate the volume of the above solid with the help of the prismatoid formula: where; V is the…

Q: PROBLEM 1 Determine the x- and y-coordinates of the centroid of the shaded area. y 0 0 ♡ 100 y = 1+1…

A:

Q: Backsight Intermediate Foresight Rise Fall ReducedLe Top Sight 1.250 0.300 0.450 0.520 0.515 0.526…

A: To approach solving questions related to identifying contour lines or similar data interpolation…

Q: a) H 20 mm 80 mm Calculate Iz 20 mm 60 mm 20 mm b) Calculate maximum Q and indicate the location on…

A: Given: A I cross section Required: Moment of inertia about Z axis Maximum value of Q

Q: Q. locate the Centroid for the following areas: y 4 0.3m 0.3m 0.5m ++ 0-43 0-2m Figure (2) Note:…

A: Figure is as shown

Q: PROBLEM 2 The centroid of the T-section shown is 2.5 inches above the base. What should be the value…

A:

Q: answer this too please y bar put 3 demicals if possible

A: Centroid y = (A1y1-A2y2)/ (A1-A2)

Q: Given: |Change in length of BE=0.00352a mm Area(BE)=150a mm? E Area(CF)=150a mm? E=200 GPa Required:…

A: To find the change in length of CF-

Q: B• 400 Turget -7-

A:

Q: cos² v dx + tan y dy dr ||

A: To find:- solution of x cos2y dx + tany dy = 0

Q: Determine the X¡ and YT(using both a and b) a. Using the Top Most, Left Most Reference Line b. Using…

A:

Q: The moment diagram by parts are base on the moment diagram of O Fully restrained beam O Cantilever…

A: Moment diagrams by parts is a method to solve the determinate beam and find reactions in beam.

Q: determine: a) the differential area b) centroid from x and y axis

A:

Q: Show step by step solution

A: FINAL ANSWER:-       Therefore,the minimum coefficient of friction is 0.2167.Explanation:

Q: Estimate the reinforcing bar of a continuous beam supported by 3 columns (400 mm x 400 mm) spaced at…

A:

Q: Calculate vertical components at point C

A:

Q: -r = 100 mm 50 mm

A:

Q: ー Fe そしい い、 Wr Wz トL2一米一しいる一 い、ta LV3= Fa-Pa9ん しいまh W:PgV 23.

A: First we need to consider a small element to get the force acting on it from high we can find the…

Q: a) top most, lef tmost FIND: b) botton-most, right-most 3cm S.ם r= 1.25 y 125 } 05 Vb cm 1.5 3 I 1,5…

A:

Q: 22. From a triangular steel plate XYZ, a triangular section VWZ was cleanly cut off. What should be…

A: Value of x is to be determined for which the line YWZ remains horizontal

Q: Find shape factor Q about the y-axis.

A:

Q: 1200 kN 300 mm 300 mm

A:

Q: Find the internal force 291.1 mmm. A D0₁ = 41. Tay= 220mm =50N B www.lbl ↓ TOON 02-623 ·100mm- 540…

A: Given truss with vertical load=100 N and it is asked to determine the internal force in each member.

Q: 5 \frac{4}{5}-2 \frac{1}{5}

A: Tofind:- difference

Q: Find the centroid along x- axis of the shaded area. x - axis = mm. 40 165 105 40 240 Dimensions in…

A:

Q: Find the centroid of the area of a trapezoid that has two equal slanting sides, a 1 Zin base and a…

A:

Q: Compute the area of each part by using proper formula.

A: Given:- stationing of O=22.5m,OA=2m; Stationing of D=19m,OB=5m=PQ Stationing of C=18.60m,ET=12m To…

Q: 6kN 2 kN\m 3 kN D 6kNm A B A CA 6m

A: