A coil of unknown resistance is placredin the left gap of meter bridge and d resistanceR is placed in right gap. The null point is,obtained 40 cm from left end. Whenresistance of 10 Q is connected in series withthe coi! and the same resistance R is kept inright gap, the null point is obtained at thecentre of wire. Find resistance of coil.

In this question we will find resistance of coil used in bridge....

A coil of unknown resistance is plaCre in the left gap of meter bridge and a resistance R is placed in right gap. The null point i obtained 40 cm from left end. When a resistance of 10 Q is connected in series with the coi! and the same resistance R is kept in right gap, the null point is obtained at the centre of wire. Find resistance of coil.

A coil of unknown resistance is plaCre in the left gap of meter bridge and a resistance R is placed in right gap. The null point i obtained 40 cm from left end. When a resistance of 10 Q is connected in series with the coi! and the same resistance R is kept in right gap, the null point is obtained at the centre of wire. Find resistance of coil.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across Ri, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) D1 IN4001 RL out OV 10 kN IN4001 alll
In DC / DC switching circuits, a resistor-inductance (r-l) circuit is usually connected to the load in series, and also a reverse parallel switching diode is connected to this inductance (l). Write down your comments and approaches about the purpose for which these connected resistance, inductance and diode elements are used by an engineer's approach
Please help with the solution.
I need the answer quickly
A platinum coil has a resistance of 3.146 at 40OC and 3.767 at 100OC. Find the resistance at 0OC and the temperature –coefficient of resistance at 40OC. Major Topic 8 Temperature coefficient of resistance EV Sco
Question 29 Factoring is a powerful simplification technique in Boolean algebra, just as it is in real-number algebra. Show how you can use factoring to help simplify the following Boolean expressions: a) d) C+CD ABC + ABC XYZ + XYZ + XYW DEF + AB+DE+0+ ABC
2. A C-core with a gap of 0.0001m has a coil number of 100 and a current of 10mA. First find the reluctance of the core given that the Iron core has a negligible reluctance and only the air reluctance contributes to the majority of reluctance. The core has a cross sectional area of 2cm². Next find the flux flowing thru the C-core.
I need the answer as soon as possible
Conductors A and B are connected in parallel. Their respective specific resistances are in the ratio 36 : 25. The former carries 20 per cent more current than the latter and the latter is 35 per cent longer than the former. Determine the ratio of their cross-sectional area(A:B).
A 500 ohm resistor is connected to a 12V source at one terminal and a 10V zener diode of 250 mW and a 5K ohm resistor are connected to the other terminal. What is the maximum current of the zener diode?
please solutions a and b and explain
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across R1, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) D IN4001 R1 V out 10 kN D2 IN4001 allle