A closely coiled helical spring is to carry a load of 500N. Its mean coil diameter is to be 10 times that of the wire diameter. Calculate these diameters if the maximum shear stress in the material of the string is to be 80MN/m^2.

A closely coiled helical spring is to carry a load of 500N. Its mean coil diameter is to be 10 times that of the wire diameter. Calculate these diameters if the maximum shear stress in the material of the string is to be 80MN/m^2.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Two concentric plain helical springs of the same length are wound out of the same wire circular in cross section and supports a compressive load P. The inner spring consists of 20 turns of mean dimeter 160 mm and the outer spring has 18 turns of mean diameter 200 mm. Calculate the maximum stress induced in the spring if the diameter of wire is equal to 10 mm and Pis equal to 1000 N. (Take K,-1)
A helical compression spring is used to absorb heavy vibrations. Apply mechanical engineering design theory and by using the values given in the table below, (i) Calculate the force applied on the spring. (ii) Determine the number of turns. (iii) Determine the spring stiffness. (iv) Calculate the free length. (v) Would you recommend to increase the number of turns and free length of the spring for this application ? Why? (answer in one/two sentences only). Spring data Туре Helical squared and ground ends Initial Compression of spring 20 mm Further Compression of spring after applying heavy load Shear Stress Modulus of rigidity 60 mm 500 N/mm2 82000 MPa Wire diameter 10 mm 6. Spring Index
please show all steps
A composite spring consists of two close-coil helical springs connected in series. Each spring has 14 coils at a mean diameter of 20 mm. The stiffness of the composite spring is 800 N/m. If the wire diameter of one spring is 2.5 mm, find the wire diameter of the other. What will be the maximum load which can be carried by the composite spring and the Take G=78 GPa. corresponding deflection for maximum shear stress of 150 MPa?
Don't try if you don't know. I need full explanation
a helical compression spring with squared and ground ends is ti be made of a steel wire 79 gpa and presetting is to be used. the operation load of the spring can be considered static. If the maximum working force is 292 N and a force of 35 N is required when the spring is 30 mm longer, determine the spring constant k
0:07I | ZVAO K/s a 15all KOREK A locs.google.com 11 Q2: The extension spring shown in the figure has full-twisted loop ends. The material is AISI 1040Q&T 400FO wire. The spring has 82 coils and is close- wound with a preload of 18 Ibf. (a) Find the closed length of the spring.(b) Find the torsional stress in the spring corresponding to the preload.(c) Estimate the spring rate.(d) What load would cause permanent deformation?(e) What is the spring deflection corresponding to the load found ?in part d 0.162 in 1 in L-in R -in R. Option 1 O
(i) Calculate the force applied on the spring.
Can you please help me with question 2. Thank you.
i need the answer quickly
Please solve this question.
Compare the differences between brittle and ductile materials. Give an example for each material with their corresponding mathematical expressions. A horizontal shaft of 75 mm in diameter and 350 mm in length projects from a bearing as shown in Figure Q4. The vertical load of 10 kN, horizontal compression load of 12 kN and torque, T' Nm are applied at the free end of the shaft. If the safe stress for the material is 145 MPa and assuming the Poisson's ratio is 0.3. Determine the torque, T to which the shaft may be subjected using the following theories: i) The Tresca Theory, and ii) The Von Mises Theory 10 kN Bearing ·· 350 mm Figure Q4 12 kN