A closed cylindrical vessel of diameter 0.65 m is half filled with water and then rotated with its axis horizontal at a speed of 600 rpm. If the water rotates as a forced vortex at the same angular velocity as the vessel and takes the form of a cylinder with a hollow core, what would be the total axial thrust tending to burst the flat ends? Also determine the total axial thrust on the flat ends if the cylinder is completely filled with water and rotated with its axis horizontal at the same speed.

A closed cylindrical vessel of diameter 0.65 m is half filled with water and then rotated with its axis horizontal at a speed of 600 rpm. If the water rotates as a forced vortex at the same angular velocity as the vessel and takes the form of a cylinder with a hollow core, what would be the total axial thrust tending to burst the flat ends? Also determine the total axial thrust on the flat ends if the cylinder is completely filled with water and rotated with its axis horizontal at the same speed.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Calculate all the reactions in the given beam. Indicate its direction in the final answer.
Q7- Air flowing with a Mach number of 2 with a pressure of 80 kPa and a temperature of 30 °C passes over a component of an aircraft that can be modeled as a wedge with an included angle of 8° that is aligned with the flow, the flow is turned through an angle of 4 leading to the generation of an oblique shock wave. Find the pressure acting on the surface of the wedge. M 2 P = 80 kPa T = 30°C
In the figure provided below: determine the vertical reaction at Point B and E.
The average linear velocity of water at the entrance of a funnel is 0.7 m/s and it increases to 7 m/s at its end which is at a distance of 0.105 m. Determine the convective acceleration at the end of the funnel.
SITUATION. A 35kg disk rests on an inclined surface for which us=0.20 W P A B C 0 Zoom image Determine the reaction at B. a b
A 60° bend occurs in a water pipeline that reduces from 600 mm diameter to 300 mm diameter at the bend (inside bend angle 120). If the gauge pressure at the inlet is 172 KPa, determine the magnitude ad angle of the thrust on the bend when the flow is 0.85 m/s. Hint: start by calculating the initial and final velocities, then the final pressure. Next, analyze the pressure and momentum forces in the x and y planes.
Given is the 200mm X 400 mm rectangular beam below. 9 kN 7.50 kN/m 400 mm 1.50 kNm A B 200 mm 1.50m 7.50m R2 R1 Figure 1 What is the reaction R2 in kN?
Each propeller of the twin-screw ship develops a full-speed thrust of F = 325 kN. In maneuvering the ship, one propeller is turning full speed ahead and the other full speed in reverse. What thrust P must each tug exert on the ship to counteract the effect of the ship's propellers? Assume a = 55 m, b = 138 m, c = 13 m. # J: F
A rectangular, fully enclosed tank 2.85m long, 1.85m wide and 0.8m high is constructed of sheet metal weighing 340N/m2. The tank floats in sea water of density 1025kg/m3 with its 0.8m sides vertical. If the centre of gravity is at the geometric centre of the vessel, calculate the metacentric height and comment on the stability of the tank.
The barrel of oil rests on the surface of the scissors lift. Determine the maximum pressure developed in the oil if the lift is moving upward with (a) a constant velocity of 4 m/ s, and (b) an acceleration of 2 m/s2. Take po = 900 kg/m2. The top of the barrel is open to the atmosphere 1.25 m
an open circular cylinder of 20cm diameter and 120cm long contains water up to a height of 80cm. It is rotated about its vertical axis 400rpm. Find the difference in the total force in N at the sides of the cylinder due to rotation.