A close-coiled helical spring, with the coil diameter as 100 mm and wire diameter as 12 mm consist of 16 coils. If it is subjected to an axial tension of 400 N, find maximum stress induced in the coil.

Q: What is the correlation between specific volume and total volume?

A:

Q: What is the overall density? %

A: This question is related to the Soil Mechanics from Civil Engineering.

Q: How is ThOD solved?

A: THOD  Theoretical oxygen demand (ThOD) is the calculated amount of oxygen required to oxidize a…

Q: With the measurements in the following table, calculate the soil moisture flux q (cm/day) between…

A:

Q: Explain the principle of 5S in Construction. Complete the answer please.

A: Introduction- Construction- It refers to the methods and business associated with assembling and…

Q: Could you show the calculations for the table

A: The discharge through the section = Q = 100, 150, 200, and 250 cfs The slope of the section = S =…

Q: 4. Why the lines on the graph do not pass through the origin?

A: When any graph line does not pass through the origin, it means that when the input equals…

Q: What is a secant Modulus?

A: Secant modulus:

Q: Define Weight-Volume Relationships

A: The weight volume relationship is depicted in following properties:- Void ratio:- The ratio of…

Q: Define Dilatancy.

A: Dilatancy is the property of dense packed granular material in which the volume increases while…

Q: Define Peclet number.

A: It is defined as the ratio of the rate of advection of a physical quantity by the flow to the rate…

Q: How can I find GH, EG and FH

A:

Q: how did you get 1.5 for the first part

A: In the original question it is stated that Vmax=2 Vmin In the solution, the following is given.…

Q: Define integer ambiguities.

A: Answer The integer ambiguities are used in GPS & GNSS surveys.

Q: For the given structures, determine the degree of indeterminacy. 7. A 7

A:

Q: The Lowest level of design pattern is called a. Design Patterns b. Architectural Design Patterns c.…

A: The lowest level of design pattern is called  d. Analysis pattern

Q: What is a box model? Give the equation to represent box model.

A: The Urban air quality models has been called box models. The Figure is a schematic graph of a box…

Q: The solution came out all in one line. Making it difficult to understand. Please Can it be written…

A:

Q: where did you get 6?

A: 6 is the loading intensity at B.

Q: What does the reductent diagram look like?

A: What does the reductent diagram look like?

Q: Define the term Index Properties.

A: The index properties are the soil properties which help to identify and classify soil. These…

Q: whered did you get .2?

A: I'm proceed according to solution The difference of maximum value and minimum value of weight is 0.2…

Q: What is bulk density? own word plss type written

A: Bulk density is the ratio of total mass of soil to the total volume of soil mass.

Q: Briefly describe the CSI Specifications?

A: CSI stands for the Construction Specification Institute. CSI has introduced a common format for…

Q: Define Dynamic Replacement.

A: Dynamic Replacement is the dynamic compaction variation, and comprises of delivering energy of…

Q: some examples of the term OFFSET

A:

Q: Explain the Modified Mercalli scale.

A: The effect caused on the surface of the earth due to an earthquake is known as the intensity of the…

Q: 9- The Scale The scale of a drawing is... Lo = X Lo = Lo= e= If e 1: Full size representation. e 1:…

A:

Q: * To draw an arc angle between two intersecting lines Fillet O Block O Trim Chamfer O If we want to…

A:

Q: Differentiate initial and boundary value problems.

A: Both type of problems are similar to each other except for that boundary value problem have…

Q: For the following scale calculate the equivalent ratio scale 2inches represents 48 meters

A:

Q: What do you mean by fail safe design

A: Fail-safe designs are the methods of designs in which various techniques can be used to mitigate…

Q: Give two environmental considerations needed for material production and elaborate.

A: Environmental considerations needed for material production are very important nowadays. Because the…

Q: Functional Analysis - complete two the Blackbox model - list sub-functions at list 5 critical…

A: In functional analysis, a Blackbox model is a representation of a system where the internal workings…

Q: For the given structures, determine the degree of indeterminacy. 1. ♫

A: This question is related to the Structure analysis

Q: i need all parts of question on the right hand corner solve I STATED FILL IN THE BLANKS.

A: Only 3 subparts can be answered at a time according to guildlines. Please resubmit the question…

Q: What is Micropiles?

A: - A Micropile is a type of friction pile having diameter less than equal to 305 mm which can be…

Q: Explain Phase Estimating

A: This hybrid or phase estimation technique is a technique of a project’s costs and the duration…

Q: Mintzberg's design parameters are- Position, superstructures, lateral linkages, and decision making…

A: Brief concept- Mintzberg's design- The organization is divided into the following key categories…

Q: Define the following words Tesserae Kline  Klismos Chai

A: These three terms give various elements that are important in design and art. Learning these will…

Laws of Equilibrium

A body is said to be in equilibrium if the system of forces acting on the body tends to keep the body at rest, in other words, there is no translation motion or net torque on the body. Under such conditions, the equilibrium conditions are to be applied to analyze the condition. The branch of mechanics that deals with this condition is known as 'statics'. Under equilibrium, there are no net forces on the body.