Answered: A circular steel bar is subjected to…

A circular steel bar is subjected to various forces as shown in Fig. determine: 1) P 2) The total elongation in the bar 3) Stress in each section Where: E = 2x10$ N/mm2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A rigid beam is supported by two elastic bars. If the temperature of these elastic bars increases by…

A: Given: a = 20 cm b = 30 cm c = 20 cm l1 = 50 cm l2 = 40 cm F = 1 kN Bar BG: A1 = 10 cm2 E1 = 2 *…

Q: ... - 24 in.-20 in.→ 20 in. 16 in. 8 in.I 8 in. The above figure is a section of a column. If the…

Q: D A 10kN 28kN + → 60KN 44KN + 120cm 80cm Ост 40cm Figure 1 a) Draw a Free Body Diagram for each…

Q: 23) A steel rod with a cross-sectional area of 150 mm² is stretched between two fixed points. The…

Q: Q2) Layers of Brass, Steel and Aluminum are bonded together and formed section shown below.…

Q: A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as…

A: GIVEN DATA A COMPOSITE ROD AXIALLY LOADED GIVEN WE HAVE TO FIND STRESS IN EACH ROD Load P=3800lb…

Q: Question 3 Based on the diagram below a) Find the internal forces of A, B & C. 950 тm 045 тm Ø30mm F…

A: First we need to calculate the reaction from the wall by balancing all the forces. Sum of all the…

Q: Shear Strain A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q…

Q: 1. The rigid link ABC is supported by a pin at B (which is connected in double-shear) and a steel…

A: ◆ First of all, calculate tension developed in the wire CD by taking moment about point B. ◆ The…

Q: The eyebolt shown in Figure below, the allowable shear stress for the supporting material is Tallow…

A: Given data Allowable shearing strength=48MPa

Q: B3 a) b) The aluminium bar shown in Fig QB3 is subjected to a plane state of stress (ox = 400MPa, ay…

Q: Q1. For the given cube below, complete the following: 1.find the center, radius (R), principal…

Q: Find the shear stress (in psi) exerted on the member shown in the figure if load (V) = 55 6b kips…

A: Problem 1: Given data: Load, V = 55.66 kips = 55.66×1000 = 55660 pounds. Area, A = 105.85 in2…

Q: Q2: A rigid platform weighing 53.5 kN is supported by three equally spaced rods. The arrangement is…

A: Given that, Weight of platform, W=53.5 kN,Temperature rise, ∆T=55.5 °C, Consider the properties as…

Q: 2.4. The stress at a point is defined by the components Og =0 MPa, Oyy =100 MPa, Oxy = Oyx = -40…

A: Given Data⇒σxx=0 MPaσyy=100 Mpaσxy=σyx=-40 MPaProblem definition⇒Problem says find principle…

Q: 4. A force Q is applied to a rectangular member with a size of 300mm x 450mm. Q is located 37.5mm…

A: Find the stress at point C and D and also find the value of force Q.

Q: Bi-axial state of stress at a point is shown below. What will be the value of principal stresses and…

A: From the given figure, σx = 100 MPa σy = 80 MPa τxy = 50 MPa

Q: Q2. A bronze bar is fastened between a steel bar and an aluminum bar as shown below. Axial loads are…

A: Es =200 GPa Eal = 70 GPa Eb = 83 GPa Cross sectional area of steel = 480 mm2 Cross sectional area of…

Q: Problem 2: A pressure vessel with p = 200 psi internal pressure is subjected also to a twisting…

A: Given data, Applied internal pressure, P = 200 psi Applied twisting moment, T = 450 kips Internal…

Q: Q.1) For the figure given below, a force P in kN determine the following. a. The location of maximum…

A: For solution refer below images.

Q: Q3) a) Draw the free-body diagram for beam shown in the figure and determine the internal normal…

Q: three rivets of 25 mm diameter joins the plates that are each 130 mm wide The shearsress in the…

A: The given data are: d=25 mm=0.025 mb=130 mm=0.13 mτr=80 MPa=80×106 Paτb=120 MPa=120×106 Pa Here, d,…

Q: Q2) Find the stress in steel rods BD and CE as shown in Figure due to the applied load 4 kN and the…

Q: A rod is composed of copper and steel section rigidly bolted in the wall as shown in the figure. If…

Q: Hertz contact theory can be used to determine the stresses due to contact between two spheres, which…

A: It is asked to find the stress by using Hertz contact theory

Q: The rectangular bar will be fabricated with an inclined glued joint at the mid-section as shown in…

Q: Problem 2. Amaterial element in plane stress is subjected to stresses: = -5000 psi Ox Oy = -2000 psi…

Q: The gap between the aluminum bar AB and the magnesium bar 0.2 m 0.25 m CD is 0.4 mm when the…

Q: Determine the sheer stress in the rivet in MPa( 3 decimals)

A: Given data: P=14.072 Nd=27 mmt=25 mmNumber of rivets (n)=7 Need to determine the shear stress in the…

Q: b) An aluminium rod is attached between a steel rod and a bronze rod as shown in Figure- 3. The…

A: Given data: The area of steel bar is As=550 mm2 The area of Aluminium bar is Aal=400 mm2 The area of…

Q: 2.2 in. in.- A IB = in. 1.6 in. e maximum and average stresses in sections A and B, take t = 0.45 in

A: Stress concentration is defined as the localization of high stresses due to the irregularities…

Q: Two identical plates are connected by two 25-mm diameter rivets as shown. Consider the following…

Q: Determine the values of the stress in the steel bar as shown in the figure below when the…

A: Find the stress and force in the bar.

Q: The stress-strain diagram for a bar of steel alloy is shown. Determine: a) The modulus of Elasticity…

A: Note:-As per our company guidelines, we are supposed to answer only the first three sub-parts.…

Q: The state of stress at a point in a tension member is given by oxx= o and other stress components…

Q: a) Determine the equivalent normal-stress component ox' on an element at the same point oriented 45°…

A: Given:σy=-430KPaζxy=-300KPa

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

A circular steel bar is subjected to various forces as shown in Fig.
determine:
1) P
2) The total elongation in the bar
3) Stress in each section
Where: E = 2x10$ N/mm?
30 KN
40 KN
70 KN
L=600mm
L=800mm
L=600mm
D=30mm
D=60mm
D=40mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q3: A steel rod is rigidly attached between an aluminum rod and a bronze rod as shown. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress in steel of 140 MPa, in aluminum of 90 MPa, or in bronze of 100 MPa. BRONZE = 500 mm² 4P STEEL A = 400 mm² 2.5 m 2.0 m ALUMINUM A = 200 mm² P 1.5 m 2 2P
Answer P1 and P2.
2
Asap
1
oy =510 (kg/cm2) Plane Stress In the stress element given in Figure, WITH MOHR CIRCLE; a- Determine the principal stress directions by calculating the principal stress values a nd Show in the stress quadrilateral. T=330 (kg/cm2) b- Calculate the largest and smallest shear stresses and determine their directions. oy Determine it and represent it in a stress quadrilateral.
1. At a point in a piece of elastic material, direct stresses of 92 MN/m2 tensile and -49 MN/m2 compressive are applied on mutually perpendicular planes. The planes are also subjected to a shear stress. If the greater principal stress is limited to 100 MN/m2 tensile, determine the value of shear stress. Give you answer to 2 significant figures in MN/m2
A roadway sign that weighs Py = 14 kN is supported by a structural pipe with an outside diameter of 340 mm and a wall thickness of 10.5 mm. Wind pressure on the sign creates a resultant force of P₂ = 21 kN, acting as shown. Using length dimensions of a = 5.4 m and b = 6.3 m, determine (a) the normal and shear stresses at point H. (b) the normal and shear stresses at point K. P₂ Py b H y K
A steel pipe is part of a drilling rig to build foundation piles The outer d 2 is equal to 6 in and the inner d, is 4.5 in and the steel has a value of 11000 ksi For a torque T = 150 K-in determine a) The maximum torsional shear stress in the furthest fiber b) The torsional shear stress in the internal part of the tube c) The angle of rotation per length that is produced to the tube
The normal and tangential stresses on a plane inclined at 30° to the axis of the minor principal stress are 75 N/mm2 and 20 N/mm2. The resultant stress on a plane by analytical method is
The force applied at the handle of the rigid lever causes lever to rotate 0.04 radians clockwise about the pin connection at B. if each cable is made of steel (E=200Gpa) and has a cross-sectional area of 3x10^-3m^2. Calculate a) The average normal stress in each cable? b) the force applied at E? The horizontal distance between points D and E is 200mm