A circular shaft subjected to torsion undergoes a twist of 1° in a length of 120 cm. if the maximum shear stress induced is limited to 1000 kg/cm2 and of modulus of rigidity G= 0.8 x 106 kg/cm2, then the radius of the shaft should be

A circular shaft subjected to torsion undergoes a twist of 1° in a length of 120 cm. if the maximum shear stress induced is limited to 1000 kg/cm2 and of modulus of rigidity G= 0.8 x 106 kg/cm2, then the radius of the shaft should be

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A hollow steel shaft with an outside diameter of 75 mm and a wall thickness of 5 mm is subjected to a pure torque of T = 1120 N-m. The shear modulus of the steel is G = 80 GPa. Determine the magnitude of the angle of twist in a 2.0-m length of shaft. O 0.0145 rad 0.0280 rad 0.0207 rad O 0.0192 rad O 0.0241 rad
8.19 A solid circular shaft is subjected to a torque T(in Nm), which produces a maximum shear stress of f(in N/mm²) in the shaft. The required diameter of the shaft would be
Check the cross-section for bending if the allowable normal stress is o =±120 MPa. a: + + 1 = 4 m a = 15 cm q = 3 kN/m a +
The stresses shown in the figure act at a point on the free surface of a machine component. If o = 22.4 ksi in the direction shown, determine the shear stress Txy at the point. Txy O 14.48 ksi 11.51 ksi O 13.53 ksi O 10.63 ksi O 8.84 ksi 5.0 ksi 24° 2.8 ksi
A cube of side 100 mm is subjected to an axial compressive load of 200 kN. Its lateral strain is prevented by applying uniform pressure but only one fourth of lateral strain could be prevented, then which of the following statements is/are correct? Assume E = 200 MPa and μ = 0.3. A The decrease in length in direction of load after applying pressure is 9.358 x 10-3 mm. B The uniform pressure applied has a value of 8.57 N/mm². C The uniform pressure applied has a value of 2.14 N/mm². D The increase in length in lateral direction after applying pressure is 2.25 x 10-³ mm.
The stresses shown act at a point on the free surface of a machine component. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 24.3 ksi, Sy = 2.7 ksi, and Sxy = 4.1 ksi. Assume β=25∘β=25∘. Determine the normal stresses σxσx and σyσy and the shear stress τxyτx⁢y at the point.
The cantilever T- beam is loaded as shown in the figure. 80 mm 40 kN/m NA 120 mm 2.0 m INA = 30x105 mm %3D What is the value of the flexural stress at the Neutral- Axis, NA?
The 60-mm-diameter solid shaft is subjected to the distributed and concentrated torsional loadings shown. Determine the absolute maximum and minimum shear stresses on the shaft’s surface and specifies their locations, measured from the free end.
4. Two solid shafts of different materials are rigidly fastened together and attached to rigid supports as shown in the figure together with the given section properties. The torque of 1000 N-m is applied at the junction of the two segments. Compute the maximum shearing stress developed in the assembly. Answer: TĄ = 5.57 MPa Ts = 22.0 MPa 3 m 1.5 m Ta Aluminum Steel 75 mm dia. T=1.0 kN•m Ga- 28 GN/m²? 50 mm dia G, - 83 GN/m?
The shaft is supported by a smooth thrust bearing at A and a smooth journal bearing at B. (Figure 1) If the shaft is made from a material having an allowable shear stress of Tallow = 70MP , determine the maximum value for P Figure 1 of 1 1m 1m 1 m 30 mm 40 mm
finding the principle stresses and stress concentration, bending stress, shear stress D D= 0. 375in lin F MA t. 2in F=200lb, W=100lb at the bend
Two flat parallel plates are separated by a small gap h filled with an incompressible fluid of viscosity u. Assume that the length and width of the plates to be much larger than the gap h. The top plate moves horizontally with a velocity V while the bottom plate is held stationary. The magnitude of the difference between the shear stress at the top and bottom walls is found to be At. Velocity of the top plate is?