A circular shaft having diameters D and a groove of radius r (with M = C = 0) is made of steel with the allowa

Q: An aluminum alloy [E = 10,000 ksi; Oy = 40 ksi] pipe (1) is connected to a bronze [E = 16,000 ksi;…

A:

Q: Compute for the linear weight of 10 mm reinforcing bar. (Use the unit weight of the Steel). a 0.692…

A: Solution  Given the dia of steel d= 10mm  So the area will be A=π/4 * 10² 24=25π mm²

Q: DETERMINE THE AVERAGE PUNCHING SHEAR STRESS THE CIRCULAR SHAFT CREATES IN THE METAL PLATE THROUGH…

A:

Q: Three plates are welded together to form the section shown. Dimensions of the cross section are b =…

A:

Q: 2. A vertical member of a steel truss is subjected to a live load of 25 kN and a service dead load…

A: LL = 25 kNDL = 50 kNU = 1.0Plate dimensions: 10 x 100 mmFactored load:P = 1.2 DL + 1.6 LL = (1.2x50)…

Q: Three plates are welded together to form the section shown. Dimensions of the cross section are b =…

A: First we need to divide the section into 3 different parts. Then we need to calculate the neutral…

Q: 3 m 1.5 m hinge A B E D 2 m 4 m

A:

Q: If a horizontal force of P = 100 N is applied perpendicular to the handle of the lever at A,…

A: FBD of the given problem:

Q: Determine the internal forces for members BC, CF and CG. 2 kN A 2 m В 2 m 2 m D SN kN 3 m F E

A:

Q: For the connection shown, the bolt diameter is d = 15 mm.  The average shear stress in the bolts…

A:

Q: P1.020 For the clevis connection shown in the figure, determine the maximum applied load P that can…

A: d = 15 mm  = 75 MPa

Q: G K H

A: Given data:

Q: Check the stability of truss.. Give me right solution with clear calculations.

A:

Q: An aluminum alloy [E = 10,000 ksi; σY = 40 ksi] pipe (1) is connected to a bronze [E = 16,000 ksi;…

A: Given data: pipe 1: (aluminum) outside diameter = 2.3 in wall thickness = 0.21 in Length = 7 ft E =…

Q: Solve the plate shown in the figure, Include fbd on solutions

A:

Q: The bolt in the figure below is 1 in. in diameter. If the load P is 10 kips, determine the average…

A: Given-Bolt diameter= 1 inchLoad, P=10kips

Q: Show complete solution (show how you achieve the member forces , e.g method of joints/method of…

A: Given : 2D truss solve using consistent deformation EI = constant

Q: Consider the beam and loading shown. NOTE: This is a multi-part question. Once an answer is…

A:

Q: An aluminum alloy [E = 10,000 ksi; σy = 40 ksi] pipe (1) is connected to a bronze [E = 16,000 ksi;…

A:

Q: Question 3. in the truss shown, a-5m, b 4m, and c=4 m Determine the force in member BE is kN. Use ve…

A:

Q: Given the truss and loading shown below, determine the stress at member FC if P₁ = 18.375 Kips and…

A:

Q: Three plates are welded together to form the section shown. Dimensions of the cross section are b =…

A:

Q: Three plates are welded together to form the section shown. Dimensions of the cross section are b=…

A:

Q: LBC LAB

A:

Q: A=7 B=7 D=2 C=5 E=8 F=4 Change letters into numbers... Determine the total area (mm2 ) of the given…

A: step 1-

Q: Problem 2: Method of Joints Inputs: ● ● ● ● h = 3.6 ft L₁ = 6.6 ft L₂= 3.0 ft F₁ = 9 kips There is a…

A:

Q: 8 kips 4 kips 4 kips d, =2" 15 kips 15 kips -d2 =1.5" !0 kips 20 kips d, =3" A Fig. for Problem #2

A: There are 3 bars AB, BC, CDThe forces on those bars are also given.Diameter of bar CD, d1 = 2…

Q: An aluminum alloy [E = 10,000 ksi; Oy = 40 ksi] pipe (1) is connected to a bronze [E = 16,000 ksi;…

A: Given, The Aluminum alloy, Modulus of Elasticity of aluminum, E1=10000 Ksi. Modulus of Elasticity of…

Q: Calculate the normal stresses from the bending moment at the bottom point of cross-section C. Data:…

A:

Q: A compound shaft consists of brass segment (1) and aluminum segment (2). Segment (1) is a solid…

A:

Q: The lap joint as shown is fastened by the 20mm diameter rivets. Assuming that the load P=50kN,…

A: This question is related to the Design steel structure.

Q: An aluminum alloy [E = 10,000 ksi; σY = 40 ksi] pipe (1) is connected to a bronze [E = 16,000 ksi;…

A:

Q: se that in addition to the 2.00-kN downward force acting at point D, a 1.85- ownward force acts at…

A: To find force in member AB, AC

Q: X Incorrect Three plates are welded together to form the section shown. Dimensions of the cross…

A:

Q: solve the stresses in members DF,DG and EG using method of sections

A: Given data  Using method of section

Q: Determine the smallest allowable cross-sectional areas of each me 400 kN The working stresses are 60…

A:

Q: By inspection, determine the zero-force members in each truss. Identify the zero-force member by…

A: As per our guidelines we are suppos d to answer first three subparts. Kindly repost other part as…

Q: The bell crack mechanism shown in Figure is in equilibrium for an applied load of F, = 15KN at A and…

A: Given: Bell Crank, F1 = 15KN, θ=65° Determine F2 = ?

Q: L1 L2 C W Fig. A Fig. B

A:

Q: 2. A vertical member of a steel truss is subjected to a live load of 25 kN and a service dead load…

A: LL = 25 kNDL = 50 kNU = 1.0Plate dimensions: 10 x 100 mmFactored load:P = 1.2 DL + 1.6 LL = (1.2x50)…

Q: 12" 6" %3D4'

A:

Graphical Methods

The graphical method is a method of solving equations involving more than one variable using the Cartesian coordinate system. In civil engineering, the use of the graphical method is limited to the problems involving two variables. The graphical method has a great impact in solving the questions regarding engineering mechanics.