A circular metallic rod of length 250 mm is placed between two rigid immovable walls as shown in the figure. The rod is perfect contact with the wall on the left side and there is a gap of 0.2 mm between the rod and the wall on the right side. If the temperature of the rod is increased by 200°C, MPa. the axial stress developed in the rod is_ Young's modulus of the material of the rod is 200 GPa and the coefficient of thermal expansion is 10-5 per°C. 250 mm -0.2 mm

A circular metallic rod of length 250 mm is placed between two rigid immovable walls as shown in the figure. The rod is perfect contact with the wall on the left side and there is a gap of 0.2 mm between the rod and the wall on the right side. If the temperature of the rod is increased by 200°C, MPa. the axial stress developed in the rod is_ Young's modulus of the material of the rod is 200 GPa and the coefficient of thermal expansion is 10-5 per°C. 250 mm -0.2 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The maximum principal stress for the stress state shown in the figure is (a) o (b) 20 (c) 30 6 (d) 1.50
d) Calculate the change in temperature. Indicate increase or decrease in temperature.
A prismatic linearly elastic bar of length L cross- sectional area A, and made up of a material with Young's modulus E, is subjected to axial tensile force as shown in the figures. When the bar is subjected to axial tensile forces P, and P the strain energies stored in the bar are U, and U respectively 1 T P, P (P.+P) If U is the strain energy stored in the same bar when subjected to an axial tensile force (P, + P2), the correct relationship is (a) U = U, - U, (c) U > U, + U, (b) U< U, + Uz (d) U = U, + Uz
I need the answer as soon as possible
Solve please
A thin-walled circular tube and a solid circularbar of the same material (see figure) are subjectedto torsion. The tube and bar have the samecross-sectional area and the same length.What is the ratio of the strain energy U1 in the tubeto the strain energy U2 in the solid bar if the maximumshear stresses are the same in both cases? (For thetube, use the approximate theory for thin-walled bars.)
A 20-ft-span beam carries a dead load of 160 lb/ft anda live load of 240 lb/ft and is to consist of Hem Fir, select structuralgrade. Find the minimum size for the beam, based on shear resistance.
1. As shown in the figure, there is a gap between the aluminum bar and the rigid slab that is supported by two copper bars. At 10°C, A = 0.18 mm. Neglecting the mass of the slab, calculate the stress in each rod when the temperature in the assembly is increased to 95°C. For each copper bar, A= 500 mm² E = 120 GPa, and a = 16.8 μm/(m °C). For the aluminum bar, A = 400 mm², E = 70 GPa, and a = 23.1 μm/(m. °C). Copper Aluminum Copper 750 mm
Q.b.
Note- Dislike for wrong answers , Please solve this correctly and accurately
A pressurized cylindrical tank with flat ends is loaded by torques T and tensile forces P (see figure). P The tank has an inner radius of r = 141 mm and wall thickness t = 6.5 mm. The internal pressure p = 7.25 MPa and the torque T = 820 N m. (Assume that the structure behaves linearly elastically and that the stresses caused by two or more loads may be superimposed to obtain the resultant stresses acting at a point. Consider both in-plane and out-of-plane shear stresses unless otherwise specified.) (a) What is the maximum permissible value of the forces P if the allowable tensile stress in the wall of the cylinder is 169 MPa? (Enter the magnitude in kN.) KN (b) If forces P = 400 kN, what is the maximum acceptable internal pressure in the tank (in MPa)? MPa
175 mm A 50 mm C -225 mm -300 mm Bar ACB shown in the Figure is subjected to a uniform temperature increase of 35°C. Knowing that the diameters of AC is 50 mm and CD is 75 mm, the modulus of elasticity E is 6.0 GPa, and the thermal expansion coefficient is 100x10^(-6) ?1/°C. What is the displacement of point C