A circular metal column is to support a load of 500 tonne and it must not compress more than 0.1 mm. Given the MOE is 210 GPa, and the column is 2 m long. Calculate the cross sectional area and the diameter of the column.

Q: A tapered rod with length c = 7m and cross - sectional dimensions a = 270n mm and b = 119 mm is…

A: Asked: To determine the elongation of the given tapered rod.   Given: Length of the rod (c) = 7 m…

Q: 5. A bar which is hinged at its end point and carries a load at its free end, is suppo by two rods…

A: Considering W=6000lb as written in question

Q: Q.17 The equivalent stiffness for the system shown below is units. If flexural rigidity of beam is…

A: Now, equivalent stiffness is

Q: 2. The bar ABCD in the given figure below consist of three (3) cylindrical steel segments, each with…

A: Finding out normal stresses at each segment.

Q: YA 20 mm 20° 100 mm 80 mm M

A:

Q: The concrete (specific weight = 150 lb/ft³) seawall of the figure below has a curved surface and…

A: There will be horizontal force and vertical force on the curved surface.  The forces and the…

Q: 1. The triangular block shown in Fig. P-010 is subjected to the loads P = 1600 lb and F = 600 lb. If…

A: Given data Force F = 600 lb Force P = 1600 lb Side AB = 8 in Side BC = 6 in To resolve Force in…

Q: Q2: A rigid bar is suspended from two wires of equal lengths 250 cm as shown below. Take E,= 210…

A: given data ,ES=210GPaEb=110GPalength =250cm1)  FB+FS=10000N=10KN    →(1)Now defoemation will be same…

Q: Q.17 The equivalent stiffness for the system shown below is units. If flexural rigidity of beam is…

A: Follow next step for solution.

Q: QUESTION 2 The assembly consists of two A-36 steel rods and a rigid bar BD. Each rod has a diameter…

A:

Q: The 33-mm-diameter A992 steel rod is subjected to the loading shown. Take E= 200 GPa. (Figure 1)…

A:

Q: The truss shown in the figure below is made from A992 steel rods having a diameter of 30 mm and…

A:

Q: Q1/ Determine the resulting displacement of pin B. Assume: A1=A2= 900 mm? , E1=E2= 100 GPa , a1=a2=…

A:

Q: As shown, three steel wires, each 26 mm in area, are used to lift a mass M. Their unstretched…

A:

Q: A slender bar AB with pinned ends is held between immovable supports as shown in the figure below.…

A: A slender bar,Length = L= 3mα= 12×10-6 /°Cdiameter = d= 50mm

Q: A solid aluminum shaft 2 in. in diameter as shown is subjected to two torques in the figure.…

A:

Q: The motorcycle weighs 151 kg and the driver weighs 64 kg. Dimensions: l1 = 0,31 m and l2 = 0,23 m…

A:

Q: 2 ст 2 сm -16 ст- 2P P 2 cm 10 cm 2 m- 2 m 1 m-

A: Given  The material used for the beam has an allowable stress of 350 kgf/cm2 in tension and 1400…

Q: DETERMINE THE FORCE (Ib) FOR MEMBER AC GIVEN THE DATA BELOW: F1 = 997 lb F2 = 1,449 lb **Note: for…

A:

Q: Tigu sno A is twice as great as the reaction at B. A 2R 600 15- 200 rmine distan R B x = 4

A:

Q: 2. The figure shown is a composite shape consists of a square and a semi-circle. Determine the polar…

A: Given: A composite cross section consisting of square and semi circle Required: Polar moment of…

Q: Compute the load that will compress the combined bar a total of 0.8mm in the lenght of 2m. If the…

A: Bar length = 2 m Surrounded by 5mm thick cast iron E for steel = 200 GPa E for cast iron = 100 GPa…

Q: 2. The bar ABCD in the given figure below consist of three (3) cylindrical steel segments, each with…

A:

Q: F=250 lb 30 45° F = 375 lb |3D

A:

Q: A box section of length L = 6 m and cross-sectional dimensions of a 52 mm, b = 44 mm has wall…

A:

Q: 342 Strength of Materials 16. A steel post (E = 200 GPa) having thickness t = 3 mm and height L = 2…

A:

Q: Compute using Euler's formula: A square aluminum bar is to support a load of 65kN on a length of…

A:

Q: A solid, circular, cast-iron bar (E = 12.5 X 106 psi, ν = 0.3) of diameter 2.13 inch, and height 15…

A: Poisson's ratio is the ratio of longitudinal strain to the lateral strain. Longitudinal strain is…

Q: The triangle section AB beam, bearing the load F1 = 400 daN in the figure, is produced from a…

A: FOS=3 width of triangular beam b=8 cm FOS=ultimate shear stressworking shear stress   3=1800working…

Q: As shown in the figure, a rigid beam with negligible weight is pinned at one end and attached to two…

A:

Q: thank

A:

Q: A T-beam with drawn x and y axes is shown in figure 2. Determine the moments of inertia of the beam.

A:

Q: 4. A nylon [E = 360 ksi; v= 0.4] rod (1) having a diameter of dl = 2.50 in. is placed inside a steel…

A:

Q: SITUATION. The figure shows a pellet about to be fired from a sling. The total unstretched length of…

A: What is the force in each leg of the rubber,F=?

Q: A EI B EI č EI D -L -L - -L +

A:

Q: The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I = 1850…

A: To find deflection at point A and B

Q: The steel block shown in Figure is subjected to a compressive force on all directions. Determine the…

A:

Q: The BC rod in the carrier system shown in the figure has a circular cross section. diameter 25 mm…

A:

Q: A O L L + The steel structure is loaded as shown. hc = 4 m, Lb = 3m, P = 40 KN, E = 200 GPa,lb= lc…

A: Given Data: hc=4mLb=3mP=40kNE=200Gpa   = 200×103MpaIB=Ic=100×106mm4To calculate:-Horizontal…

Q: A rectangular block is 137 mm long in the X direction, 93 mm wide in the Y direction, and 56 mm…

A: Strain will be equal in 1st and 2nd case as length is same. Comparing deformation and strain will…

Q: A beam 1 = 0.8 m long is acted on by three forces, as illustrated below. The beam is in equilibrium…

A:

Pressure and Stress